Abstract:Commonly used alkali activation precursors such as blast furnace slag and fly ash will soon become less available due to resource competition, and may cease to be produced in certain regions. This limitation in future supply is a main driving force for the investigation of alternative precursor sources, such as non-blast furnace slags and non-ferrous slags, to produce alkali-activated binders. The current study investigates the incorporation of copper slag (CS) and stainless steel slag resulting from electric arc furnace operations (EAFSS) as partial replacements for ground granulated blast furnace slag (GGBFS) in producing alkali-activated materials (AAMs), at paste level. Five binary alkali-activated mixtures with different replacement levels of GGBFS with CS, and three ternary mixtures with both CS and EAFSS as partial and total replacements for GGBFS, are activated by a sodium silicate solution. Replacing GGBFS with CS and EAFSS retards the reaction kinetics, resulting in improved fresh-state properties of the investigated AAMs, better retention of workability and longer setting times. The reaction of alkali-activated 100% CS shows minimal initial exothermic activity until 3.5 h, when a single intense peak appears, representing delayed dissolution and subsequent polycondensation. X-ray diffraction (XRD) data indicate that the main crystalline phases of CS and EAFSS are stable in these alkaline systems; it is the glassy components that react. The use of CS and EAFSS in blended AAMs causes a minor increase in porosity of ~ 1–3% with respect to GGBFS only, and a small reduction in compressive and flexural strengths, although these reach 80 MPa and 8 MPa, respectively, after 28 days, even at a replacement level over 65 wt. %. Conversely, the 100% CS mixture exhibits a one-day compressive strength of 23 MPa, with a negligible increase thereafter. This result agrees with both FTIR and SEM analysis which highlight only minor changes in binder development after two days. It is believed that the unusual behaviour of CS in the investigated mixtures is related to the low availability of calcium in this precursor material.

Determination of the apparent activation energy for composite binder containing blast furnace ferronickel slag

Hydration heat and kinetics of composite binder containing blast furnace ferronickel slag at different temperatures

Activation of Blast Furnace Slag with CFB Fly Ash as a Supplementary Binder Material: Hydration Products and Effects of Sulfate Attack

Insight into the performance of composite binder with high-volume steel slag, blast furnace slag and desulfurization gypsum

Hydration Kinetics of Composite Binder Containing Slag at Different Temperatures

Effect of Water-to-binder Ratio on the Hydration Kinetics of Composite Binder Containing Slag or Fly Ash

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Preparation of Sustainable and Green Cement -Based Composite Binders with High -Volume Steel Slag Powder and Ultra Fi Ne Blast Furnace Slag Powder

Compressive Strength and Microstructural Development of Cementitious Mixtures Incorporating Ultrafine Granulated Blast Furnace Slag

Evaluation of copper slag and stainless steel slag as replacements for blast furnace slag in binary and ternary alkali-activated cements

Preparation of sustainable and green cement-based composite binders with high-volume steel slag powder and ultrafine blast furnace slag powder

Recycling Blast Furnace Ferronickel Slag as a Replacement for Paste in Mortar: Formation of Carboaluminate, Reduction of White Portland Cement, and Increase in Strength

Effect of four-component binder on characteristics of self-compacting and fibre-reinforced self-compacting mortars

The Impact of Fly Ash on the Properties of Cementitious Materials Based on Slag-Steel Slag-Gypsum Solid Waste

Blast furnace slag supersulfated cements: composition optimization, microstructures, and environmental impact

Mechanical Properties and Microscopic Mechanism of a Multi-Cementitious System Comprising Cement, Fly Ash, and Steel Slag Powder

Effect of Extracted Titanium Tailing Slag on the Properties of Alkali-Activated Fly Ash-Ground Blast Furnace Slag Binder

Deep insight into mechanical behavior and microstructure mechanism of quicklime-activated ground granulated blast-furnace slag pastes

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Preparation of steel slag-based cementitious materials compounded with GBFS and phosphogypsum: mix design, hydration, and microstructure characteristic

Study on the Alkali–Sulfur Co-Activation and Mechanical Properties of Low-Carbon Cementitious Composite Materials Based on Electrolytic Manganese Residue, Carbide Slag, and Granulated Blast-Furnace Slag