Abstract:Abstract High entropy alloy (HEA) is an advanced alloy material, which has a wide application prospect due to its excellent properties. However, the material removal mechanism and change rule of grinding force of HEA in the grinding process have seldom been studied. The main work of this paper is that the material removal mechanism of the FeCoNiCrMo 0.1 HEA is obtained by analyzing grinding debris and subsurface microstructure after grinding, the theoretical grinding force model of HEAs in plane grinding process is established on the basis of the force of a single abrasive grain, and the experimental verification is performed. According to the experimental results, the influences of different grinding parameters on grinding force are discussed, the influences of different types of grinding wheels on grinding force are analyzed, and the grinding forces generated by grinding different FeCoNiCr HEAs are compared. The results indicate that the material removal mechanism of FeCoNiCrMo 0.1 HEA is the plastic removal. With the increase of grinding speed and the decrease of grinding depth and feed speed, both normal and tangential grinding forces decrease. Under the same grinding parameters, the grinding force produced by electroplated CBN grinding wheel is greater, followed by resin-bonded CBN grinding wheel and vitrified CBN grinding wheel. The grinding force produced by grinding FeCoNiCrAl 0.1 HEA is lower than that produced by grinding FeCoNiCrMo 0.1 HEA under the same grinding conditions. The calculated value of grinding force model is consistent with the experimental value, which can scientifically reflect the variation law of HEA grinding force.

Surface Integrity Analysis in Grinding of Dual-phase High Entropy Alloy

Experimental Research on Material Removal Mechanism and Grinding Force of FeCoNiCrMo0.1 High Entropy Alloy (HEA)

Flat-end mill machining analysis of processed CrMnFeCoNi high-entropy alloys

A Hf-doped Dual-Phase High-Entropy Alloy: Phase Evolution and Wear Features

Effect of Phase Proportion on Wear Behavior of Al–Cr–Fe–Ni Dual-Phase High Entropy Alloys

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Cutting Behavior of Al0.6CoCrFeNi High Entropy Alloy

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Microstructure, Mechanical Property, and Wear Behavior of NiAl-Based High-Entropy Alloy

Alloying behavior and characterization of (CoCrFeNiMn)90M10 (M=Al, Hf) high-entropy materials fabricated by mechanical alloying

Microstructural and Tribological Behavior of Thermal Spray CrMnFeCoNi High Entropy Alloy Coatings

Microstructural, Microhardness and tribological analysis of cooling-assisted friction stir processing of high-entropy alloy particles reinforced aluminum alloy surface composites

Tribology behavior in laser cladded dual-phase Al x CoCrFeNiMn (1-x) high entropy alloys influenced by hierarchical interface architecture

Phase transformation and strengthening mechanisms of nanostructured high-entropy alloys

Microstructure and wear behavior of mechanically alloyed powder AlxMo0.5NbFeTiMn2 high entropy alloy coating formed by laser cladding

Microstructure and properties analysis of FeCoNiAlCu dual-phase high-entropy alloy coating by laser cladding

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Development of Wear-Resistant Dual-Phase High-Entropy Alloys Enhanced by C15 Laves Phase

Phase evolution and mechanical properties of Al x CoCrFeNi high-entropy alloys by directed energy deposition

Tailoring Phase Transformation Strengthening and Plasticity of Nanostructured High Entropy Alloys