Abstract:Ti2AlNb (Ti-22Al-25Nb at.%, nominal composition) intermetallic is essential to aerospace industry from a weight reduction perspective, and brings a possibility of replacing some Ni-based superalloys. Despite evaporation of element Al (from its original composition 22.8 at.% to 18.5 at.%), selective laser melting (SLM) technology offers distinct advantages in fabricating Ti2AlNb intermetallic with superior room-temperature properties. A full understanding of corresponding heat treatment mechanism is the key to utilize well the SLM-prepared Ti2AlNb at high temperatures. This study aims to clarify the relationship between the microstructure and mechanical propensities of SLM-prepared then heat-treated Ti2AlNb, to ultimately achieve promising mechanical performances at high temperatures. For this research purpose, a series of heat treatments were conducted, and the corresponding microstructures, mechanical properties were systematic studied by advanced characterization techniques. Results show that the mechanical properties at both room and high temperatures depend on heat treatment adopted. The samples solution-treated at 950 degrees C and then aged at 700 degrees C show promising room and high temperature strengths due to the formation of acicular O, alpha(2) and grain boundary alpha(2) phases. However, their ductility was poor. Aging at 830 degrees C reduces the strength, but significantly improves the ductility due to the appearance of rodlike O phase and the increase of B2/beta phase proportion. The alloy possesses promising strength and ductility (611 MPa, 10.0%) and high thermal stability at 650 degrees C. It is further demonstrated that the heat-treated Ti2AlNb possesses promising specific strength, even higher than that of as-cast Inconel 718 superalloy. The developed alloy, therefore, has a high potential for the industries requiring high-temperature performance and weight reduction.

Influence of heat treatment on the microstructural evolution and mechanical performance of powder bed fusion AlSi12 and Al7050 bimetallic structures

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Effect of Heat Treatments on the Microstructure and Mechanical Properties of Ti2AlNb Intermetallic Fabricated by Selective Laser Melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Powder Metallurgy Ti-48Al Alloy

Effects of Heat Treatment on Microstructure and Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting Process

Unveiling the impact of heat treatment on powder-metallurgy α+β titanium alloy for achieving a superior strength-ductility combination

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Effect of Heat Treatment on Microstructure Evolution and Mechanical Properties of Selective Laser Melted Ti–6Al–4V and TiB/Ti–6Al–4V Composite: A Comparative Study

Effect of Heat Treatment on the Anisotropy in Mechanical Properties of Selective Laser Melted AlSi10Mg

The effect of the iso‐thermal heat treatment on the microstructure and properties of powder bed fusion‐laser beam AlSi10Mg alloy

Influence of heat treatment on the microstructure and mechanical properties of Al–Mg–Si alloy fabricated by double wires + arc additive manufacturing

Heat-treatment induced microstructural evolution and enhanced mechanical property of selective laser melted near β Ti-5Al-5Mo-5 V-3Cr-1Zr alloy

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Al-7Si-0.7Mg-2.5Fe Processed by Laser Powder Bed Fusion

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Effect of heat treatments on the microstructure and mechanical properties of IN738LC prepared by electron beam powder bed fusion

Effect of Heat Treatment on the Microstructure and Mechanical Properties of a Ti-TiAl Laminate Composite