Abstract:A discrete element method (DEM) model was developed for a co-rotating twin-screw mixer (TSM) consisting of conveying and kneading elements. This model was used to simulate the mixing of a cohesive binary system of particles (P1 and P2). The particles were calibrated using angle of repose and dynamic yield strength simulations. Properties of P1 were kept constant throughout the study while properties of P2 were varied. The TSM model was used to study the influence of particle size, density, and flowability of P2 on process outputs such as powder holdup, mean residence time (MRT), and degree of mixing along the length of the TSM. All the three particle properties were varied at three-factor levels with flowability ranging from good flow (GF), poor flow (PF), and very very poor flow (VVPF) based on Carr’s classification. The model provides fundamental insights into the differences in mixing in the conveying sections of the mixer for materials with different flowability. Due to the co-rotating nature of the screws, the majority of the material in the conveying sections was carried on one side of the TSM for GF and PF particles, while both the screws carried VVPF particles. The total steady-state holdup and the mean residence time (MRT) of particles inside the TSM were heavily influenced by particle flowability compared to the other two tested particle parameters. The holdup in the conveying compartments ranged from 11%–15% of the total holdup, while the kneading compartment comprised 40% of the total holdup in the mixer. The simulations found that VVPF particles mixed the fastest and that the GF particles had the highest tendency to demix. The model was also used to suggest and test other screw design configurations to improve mixing. A screw design with kneading elements closer to the mixer outlet resulted in better mixing of GF particles. A screw design consisting only of conveying elements achieved the same degree of mixing as the original screw design for VVPF particles.

Particle size and shape effect of Crumbler® rotary shear-milled granular woody biomass on the performance of Acrison® screw feeder: A computational and experimental investigation

The Influence of Particles' Aspect Ratio on the Shear Behaviour of Granular Materials

The Influence of Particle-Size Distribution on Critical State Behavior of Spherical and Non-Spherical Particle Assemblies

Simulation of Biomass Pyrolysis in a Rotary Drum by Coupling CFD-DEM with a One-Dimensional Thermally Thick Model

Studying on the Upper Limit of the Coarse-Grained DEM Model for Simulating Mixing Processes in a Rolling Drum with Complex Wall Boundary

Nanoparticle Deagglomeration Driven by a High Shear Mixer and Intensification of Low-Speed Stirring in a Viscous System

The influence of faceted particle shapes on material dynamics in screw conveying

Application of fluid rheology models for milled woody biomass and non-recyclable municipal solid waste particles

Discrete element modeling of switchgrass particles under compression and rotational shear

Friction and Shear Properties of Pine Biomass and Pellets

Investigating screw-agitator speed ratio impact on feeding performance in pharmaceutical manufacturing using discrete element method

An Experimentally Validated Coarse-Grain DEM Study of Monodisperse Granular Mixing

DEM Investigation on Conveying of Non-Spherical Particles in a Screw Conveyor

Effects of the Moisture Content on the Flow Behavior of Milled Woody Biomass

Characterization of biomass comminution for entrained-flow gasification

CFD-DEM Investigation of the Fluidization of Binary Mixtures Containing Rod-Like Particles and Spherical Particles in a Fluidized Bed

Impact of Particle Size Polydispersity on Chemical Looping Combustion of Biomass under a Continuous Injection Mode

Assessing processability of milled HME extrudates: Consolidating the effect of extrusion temperature, drug loading, and particle size via Non-dimensional cohesion

Investigating the effects of material properties on the mixing dynamics of cohesive particles in a twin screw mixer using a discrete element method approach

Micromechanical Investigation of the Particle Size Effect on the Shear Strength of Uncrushable Granular Materials

Investigation of mixing homogeneity of binary particle systems in high-shear wet granulator by DEM