Abstract:The effect of mechanical alloying on the development of Ni–Al–Ti–Mn–Co–Fe–Cr high entropy alloys (HEAs) utilizing the spark plasma sintering (SPS) method is the main goal of this study. A bulk sample was fabricated using SPS after the alloys were mixed for 12 h. Thermodynamic simulation, X-ray diffraction, scanning electron microscopy, nanoindentation, and microhardness were used to investigate the microstructure and mechanical properties of the as-mixed powders. The master alloy was made of NiAl and was subsequently alloyed with Ti, Mn, Co, Fe, and Cr at different compositions to develop HEAs at a sintering temperature of 850 °C, a heating rate of 100 °C/min, a pressure of 50 MPa, and a dwelling time of 5 min. A uniform dispersion of the alloying material can be seen in the microstructure of the sintered HEAs with different weight elements. The grain size analysis shows that the Ni 25 Al 25 Ti 8 Mn 8 Co 15 Fe 14 Cr 5 alloy exhibited a refined structure with a grain size of 2.36 ± 0.27 μm compared to a coarser grain size of 8.26 ± 0.43 μm attained by the NiAl master alloy. Similarly, the HEAs with the highest alloying content had a greater microstrain value of 0.0449 ± 0.0036, whereas the unalloyed NiAl had 0.00187 ± 0.0005. Maximum microhardness of 139 ± 0.8 HV, nanohardness of 18.8 ± 0.36 GPa, elastic modulus of 207.5 ± 1.65 GPa, elastic recovery ( W e / W t ) of 0.556 ± 0.035, elastic strain to failure ( H / E r ) of 0.09.06 ± 0.0027, yield pressure ( H 3 / ) of 0.154 ± 0.0055 GPa, and the least plasticity index ( W p / W t ) of 0.444 ± 0.039 were attained by Ni 25 Al 25 Ti 8 Mn 8 Co 15 Fe 14 Cr 5 . A steady movement to the left may be seen in the load–displacement curve. Increased resistance to indentation by the developed HEAs was made possible by the increase in alloying metals, which ultimately led to higher nanohardness and elastic modulus.

Mechanical and thermal expansion behaviour of TiC-reinforced CoCrFeMnNi high entropy alloy prepared by mechanical alloying and spark plasma sintering

Effect of TiC addition on the microstructure and mechanical properties of FeCoCrNiMn high entropy alloy fabricated by selective laser melting

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Enhanced tensile properties of CrMnFeCoNi0.8 high entropy alloy with in-situ TiC particles

Effect of FeCoNiMnCr High-Entropy Alloy Reinforcement on Mechanical, Wear, and Thermal Expansion Behavior of Copper Matrix Composites

The microstructural evolution and enhanced mechanical properties of in-situ Ti(C, N)-reinforced CoCrFeNiTi high-entropy alloy composites fabricated via mechanical alloying and spark plasma sintering

Boosted mechanical properties of CoCr3Fe5Ni high entropy alloy via in-situ TiC particles

Microstructures and Tribological Properties of TiC Reinforced FeCoNiCuAl High-Entropy Alloy at Normal and Elevated Temperature

Effects of Ti addition and annealing on microstructure and mechanical properties of CoCrFeMnNi high-entropy alloy

In-situ development of Ti(C, N) and their effect on microstructure,wear and corrosion properties of CoCrFeNiTi high-entropy alloy matrix composites

Microstructure and properties of high entropy alloy reinforced titanium matrix composites

Effect of TiC Addition on the High-Temperature Hardness and the Carbide Stability in Al0.2CoCrFeNi1.5Ti High-Entropy Alloy

Phase prediction, microstructure, and mechanical properties of spark plasma sintered Ni–Al–Ti–Mn–Co–Fe–Cr high entropy alloys

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Evolution of phase stability and structural properties in CrFeNiTiV high-entropy alloy under high-temperature heat treatment conditions

Nanostructured Al–Ti–Fe–Mn–Ni High-Entropy Alloy by Mechanical Alloying: Synthesis and Characterization

Mechanical properties and wear behaviors of FeCoNiCrMnTix high-entropy alloys manufactured by vacuum arc melting

Effects of Ti Content on the Microstructure and Mechanical Properties of Al0.2CoCrFeNi2Tix High-Entropy Alloys

Evolution of microstructure and mechanical characteristics of (CrFeNiCu)100–xTix high-entropy alloys

Effect of Ti on Characterization and Properties of CoCrFeNiTix High Entropy Alloy Prepared Via Electro-Deoxidization of the Metal Oxides and Vacuum Hot Pressing Sintering Process