Abstract:The main objective of this thesis is to develop a method to investigate stability behaviours of stiffened and unstiffened panels under the influence of in-plane compression and out-of-plane lateral pressure using appropriate simplifications. A test fixture to conduct buckling experiments with lateral pressure is also designed. Due to the deflection caused by the lateral pressure, considerable complexities will be introduced in terms of loading interactions and geometric nonlinearities, which make the analysis both theoretically difficult and computationally intensive. In addition, in aerospace structures, non-cylindrical wing and fuselage panels are potentially exposed to the combined action of in-plane compression and out-of-plane pressure, and the assessment of their stability behaviours becomes an issue of growing concern of structural engineers. To this end, the study of the buckling behaviour of stiffened panels under compression and lateral pressure is of practical importance. Step by step investigations are performed on typical structures from unstiffened isotropic plates to stiffened composite panels using both analytical and finite element approaches. First, linear based methods using equilibrium and energy equations based on classical plate theories are reviewed, and predictions indicate that these methods only validate within the range of small deformation under small pressure loading. Eigenvalue buckling analysis and explicit dynamic procedures are adopted as numerical methods for verification. Simulated results of explicit dynamic procedures in Abaqus predicted the buckling loads fairly well compared with those in literature, revealing that lateral pressure has a positive impact on the stability behaviour of rectangular isotropic plates by postponing the buckling onset. Composite panels behave similarly as isotropic plates in terms of buckling and postbuckling responses. Given a large pressure, the critical buckling load of a simply supported laminate is able to reach up to four times as that of the uniaxially compressed plate. A conceptual design of a test fixture for buckling experimental studies involving compression and lateral pressure is proposed in which pressurized airbags are adopted for generating uniform pressure load. The lateral loads are controlled by the internal pressure of airbags through a pressure gauge. Compression sensors are utilized to calibrate the pressure loads by measuring the reaction forces. A rubber filler pad is laid inside the panel's bays between stringers to eliminate the unevenness on the stiffener side of the panel. Test rigs are designed with the consideration of compatibility with classical buckling experiments to lower the cost. Dynamic explicit simulations of the test reveal that the locations of the first local buckling onsets are shifted from the skin to stiffeners with the increase of lateral pressure. Buckling strengths of the entire stiffened panels exhibit an increase with the increase of lateral pressure. However, this trend is reversed when the pressure load exceeded a certain value at which stiffeners buckle before the skin.

Derivation of Buckling Knockdown Factors for Pressurized Orthogrid-Stiffened Cylinders of Launch Vehicle Structures

Derivation of Knockdown Factors for Common Bulkhead Structures Considering Geometric Initial Imperfection and Heat Transfer Effects

Knockdown factor of buckling load for axially compressed cylindrical shells: state of the art and new perspectives

Modified Fourier-Galerkin Solution For Aerospace Skin-Stiffener Panels Subjected To Interface Force And Mixed Boundary Conditions

Accelerated Koiter method for post-buckling analysis of thin-walled shells under axial compression

Buckling Behavior Analysis of Thin-Walled Cylindrical Shell Structure under Localized Axial Compression Load Based on Initial Imperfection Sensitivity

Advances in Buckling Analysis of Axial Compression Loaded Thin-walled Cylindrical Shells Based on Initial Imperfection Sensitivity

A New Design Method For Axially Loaded Thin-Walled Cylindrical Shells Based On Elasto-Plastic Buckling Analysis

Design of Axially Loaded Isotropic Cylindrical Shells Using Multiple Perturbation Load Approach – Simulation and Validation

High-fidelity numerical simulation and experimental validation of a 1600-mm-diameter axial loaded grid stiffened cylindrical shell

Buckling Analysis of Variable Stiffness Composite Cylindrical Shells Under Axial Compression Considering Imperfection Sensitivity

Efficient buckling analysis and optimization method for rotationally periodic stiffened shells accelerated by Bloch wave method

Numerical Limit and Shakedown Analysis Method for Kinematic Hardening Structure Made of Arbitrary Inhomogeneous Material

Post-buckling optimization of bending-induced variable stiffness composite cylinders considering worst geometric imperfections

Isogeometric analysis-based buckling optimization framework for grid-stiffened shells using asymptotic homogenization method and Rayleigh–Ritz method

Finite Element-Based Structural Optimization of Large System Models Under Buckling Constraints

Enhanced buckling reduction factors using amplified imperfections for existing steel structures

Shakedown Analysis of Bounded Kinematic Hardening Engineering Structures under Complex Cyclic Loads: Theoretical Aspects and a Direct Approach

Stochastic Dynamic Buckling Analysis of Cylindrical Shell Structures Based on Isogeometric Analysis

The Influence of Initial Geometric Imperfection on the Localized Buckling of Pressure Vessel under Internal Pressure

A Study of the Buckling Behaviour of Stiffened Panels under Compression and Lateral Pressure