Abstract:Laser-assisted electrochemical machining (ECM) is an ideal manufacturing method for Inconel 718 (IN718) because of the method's high efficiency and good surface quality, and the basis for and key to laser-assisted ECM is its anodic electrochemical dissolution behavior. In this study, IN718 in a 10 wt % NaNO3 solution was subjected to innovative electrochemical testing and laser-assisted ECM experiments to investigate its corrosion properties and the passive film characteristics formed on its surface. The passivation-related behaviors and structures of the passive film were investigated based on open-circuit potentials, dynamic polarization, potentiostatic polarization, and electrochemical impedance spectroscopy. It was found that there was obvious active-passive-transpassive transition behavior, and the structure of the passive film in laser-assisted ECM exhibited pores and defects, resulting in weak corrosion resistance, compared with IN718 under ECM without laser irradiation. The chemical composition of the passive film was obtained by X-ray photoelectron spectroscopy. The results showed that the passive film was composed mainly of a mixture of NiO, Ni(OH)2, Cr2O3, CrO3, Fe2O3, α-Fe2O3, α-FeOOH, Nb2O5, NbO, MoO3, MoO2, and TiO2. The passive film formed by laser-assisted ECM was rich in NiO and TiO2 and lacked Cr2O3 and MoO3, which validated its pores and defect structures. A corresponding schematic model was also proposed to characterize the interface structure between the IN718 substrate and the passive film. Laser-assisted ECM tests were performed under different current densities and machining times, and the corrosion morphology of IN718 was identified. Corrosion pits and a loose product layer appeared on the machined surface at low current densities, and the dissolution mechanism was pitting. The quantity and depth of the corrosion pits dispersed on the machined surface clearly decreased as the current density increased. Finally, a quantitative corrosion model was established to characterize the dissolution behavior of IN718 in NaNO3 solution during laser-assisted ECM.

Synergistic effect of transpassive film and gamma double prime phase on the electrochemical dissolution behavior of Inconel 718 manufactured by laser directed energy deposition

Passive behavior of laser directed energy deposited Inconel 718 after homogenization and aging heat treatment

Study of Pre-Precipitated Δ Phase Promoting Deformation Twinning and Recrystallization Behavior of Inconel 718 Superalloy During Hot Compression

Electrochemical dissolution behavior of heat treated laser solid formed Inconel718

The Precipitation Behavior Effect of Δ and Γ" Phases on Mechanical Properties of Laser Powder Bed Fusion Inconel 718 Alloy

Dissolution of the Laves Phase and δ-Precipitate Formation Mechanism in Additively Manufactured Inconel 718 during Post Printing Heat Treatments

The δ Phase Precipitation of an Inconel 718 Superalloy Fabricated by Electromagnetic Stirring Assisted Laser Solid Forming

Study of the influence of the preparation method on the electrochemical dissolution behavior of Inconel 718

Effect of heat treatment on microstructure, precipitation behavior and mechanical properties of Inconel 718 fabricated by laser direct energy deposition

Effect of heat treatment on microstructure and mechanical properties of selective laser melted Inconel 718 alloy

Anodic dissolution behavior of the complex microstructure of laser directed energy deposited Alloy 718 during electrolyte jet machining in NaCl-ethylene glycol electrolyte

Effect of heat treatment on microstructures and mechanical properties of Inconel 718 additively manufactured using gradient laser power

Dissolution Kinetics and Behavior of Δ Phase in Inconel 718

Microstructure and Electrochemical Corrosion Behavior of Inconel 718 Alloy Fabricated by Selective Laser Melting

Tailoring Laves Phase and Mechanical Properties of Directed Energy Deposited Inconel 718 Thin-Wall Via a Gradient Laser Power Method

Enhanced strength-ductility synergy in a selective laser melted Inconel 718 superalloy by refining γ′′ precipitates

The effect of interval pulsed laser deposition on the microstructure and mechanical properties of Inconel 718 parts using laser directed energy deposition

Microstructure evolution of an Inconel 718 alloy prepared by electron beam smelting

A new approach to improve strength and ductility of laser powder deposited Inconel 718 thin-wall structure

Effect of electropulsing-assisted ultrasonic nanocrystal surface modification on microstructures and hardness of additive manufactured Inconel 718

Corrosion Properties and Passive Film Interface of Inconel 718 in NaNO3 Solution for Laser-Assisted Electrochemical Machining