Abstract:The as-cast microstructure characteristic and room temperature mechanical properties of Al0.4Co0.5VxFeNi high-entropy alloys (HEAs, where x = 0, 0.2, 0.4, and 0.6 in molar ratio, denoted as AC0, AC1, AC2, and AC3, respectively), fabricated by the vacuum arc melting method, were investigated by a combination of optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and tension and compression tests. The vertical section of phase diagrams of Al0.4Co0.5VxFeNi HEAs were calculated with the Pandat software to show the equilibrium phases in the alloys at varying temperatures. The results show that Al0.4Co0.5VxFeNi HEAs have dual-phase structures. AC0, AC1, and AC2 show a typical dendritic structure composed of dendritic and interdendritic phases. AC3 shows a typical dual-phase structure with the characteristics of a eutectic structure. The comprehensive performance of the Al0.4Co0.5VxFeNi HEAs is remarkably enhanced by vanadium alloying. AC0 has a microhardness of about 2.79–2.90 GPa, which is three times lower than that of AC3. With an increase of V from 0.4 to 0.6, the structure of FCC-L12 transforms into an FCC phase. The AC1and AC2 HEAs present excellent strength and ductility, with elongation of tension tests at break exceeding 30%. Compared to the tension strength of AC1 and AC2, the yield strength of AC3 increases distinctly and its ultimate strength of extension increases, which is in trade off elongation. The fractured surfaces of AC1 and AC2 are ductile fractures, but the fracture surface feature of AC3 is mainly trench-like microstructures. During tensile deformation, the FCC phase is stretched by ductile fracturing while the BCC-B2 phase shows barely deformed cleavage fracturing, which causes the FCC phase to become thinner and with protruding edges.

Microstructural evolution and duplex structure-enhanced high-temperature mechanical properties of Al-doped VCoNi medium entropy alloy

The influences of vanadium addition and temperature on the microstructure, and mechanical properties of Al 0.1 CoCrFeNiV x multi-principal element alloys

Influence of V and Al in Enhancing the Strength and Ductility of Co-rich High-Entropy Alloys

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Analysis of deformation behavior of VCoNi medium-entropy alloy at temperatures ranging from 77 K to 573 K

Effects of V Addition on the Deformation Mechanism and Mechanical Properties of Non-Equiatomic CoCrNi Medium-Entropy Alloys

Effect of Alloying on Microstructure and Mechanical Properties of AlCoCrFeNi2.1 Eutectic High-Entropy Alloy

Effect of element V on the as-cast microstructure and mechanical properties of Al0.4Co0.5VxFeNi high entropy alloys

Effect of Vanadium Addition on the Microstructure, Hardness, and Wear Resistance of Al 0.5 CoCrCuFeNi High-Entropy Alloy

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Impact of Cu Content on Microstructural Evolution and Mechanical Behavior of CoCrMo0.5TiVCux High-Entropy Alloys

The microstructural characteristics and high temperature mechanical properties of quaternary Ti–V–Al–Co shape memory alloys

Quasi-superplasticity in the AlCoNiV Medium Entropy Alloy with Heusler L21 Precipitates

Tuning Microstructures and Tensile Properties of the CoNiV Medium Entropy Alloy by Minor Alloying

Development of Co–Ni–Al–V–Ta–Cr-based superalloys with high-temperature strength and excellent oxidation resistance

Ultrahigh grain boundary strengthening ability of VCoNi medium entropy alloy

Effect of Al addition on the microstructure and hardness of the (AlxCoCrFe)50Ni high-entropy alloy prepared by directed energy deposition technique

Effects of Al content on microstructures and high-temperature tensile properties of two newly designed CoNi-base superalloys

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Microstructure and Mechanical Properties of Novel CrCoNi–Al2O3P Medium Entropy Alloy-Matrix Composites