Abstract:The stacking fault energy (SFE) of face-centered cubic (FCC) alloys is a critical parameter that controls microstructural and crystallographic texture evolution during deformation and annealing treatments. This review focuses on several FCC alloys, aluminum (Al), copper (Cu), austenitic stainless steels (ASSs), and high entropy alloys (HEAs), all of which exhibit varying SFEs. These alloys are often subjected to thermo-mechanical processing (TMP) to enhance their mechanical properties. TMP leads to the evolution of deformation-induced products, such as shear bands (SBs), strain-induced martensite (SIM), and mechanical/deformation twins (DTs) during plastic deformation, while also influencing crystallographic texture. High-medium SFE materials, such as Al and Cu, typically exhibit the evolution of Copper-type texture during room temperature rolling (RTR), while low SFE materials, such as ASSs and HEAs, display Brass-type texture at high reduction ratios. Moreover, the presence of second-phase particles/precipitates can also impact the microstructure and texture evolution in Al and Cu alloys. Particle-stimulated nucleation (PSN) during the annealing treatment has been reported for Al, Cu, ASSs, and HEAs, which causes texture weakening. Another interesting observation in severely deformed Cu alloys is the room-temperature softening phenomenon, which is discussed in the reviewed work. Additionally, plastic deformation and heat treatment of ASSs result in phase transformation, which was not observed in Al, Cu, or HEAs. Furthermore, the dependence of special boundaries in HEAs on plastic deformation temperature, strain rate, and annealing temperature is also discussed. Thus, this review comprehensively reports on the impact of TMP on microstructural and crystallographic texture evolution during plastic deformation and the annealing treatment of Al, Cu, ASSs, and HEAs FCC materials, using results obtained from electron microscopy.

Influence of grain boundary modification on color transition behavior of Cu-Al-Zn-Sn alloys with low stacking fault energy

Influence of Grain Orientation and Grain Boundary Features on Local Stress State of Cu-8Al-11Mn Alloy Investigated Using Crystal Plasticity Finite Element Method

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Theoretical Investigation of Cu Influence on the Stability Characteristics of T-phase in Crossover Alloys

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Strain hardening behavior and microstructure evolution of gradient-structured Cu-Al alloys with low stack fault energy

Effect of Short-Range Ordering on the Grain Boundary Character Distribution Optimization of FCC Metals with High Stacking Fault Energy: A Case Study on Ni-Cr Alloys

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Amorphous complexions alter the tensile failure of nanocrystalline Cu-Zr alloys

Fracture Behavior and Structural Transition of Ni46Mn33Ga17Cu4−Zr Alloys

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

Plastic Deformation Mechanisms in Face-Centered Cubic Materials with Low Stacking Fault Energy

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Tailoring the formability and planar anisotropy of Al-Mg-Si-Cu-Zn alloys via cross hot rolling and two-stage cold rolling

Influence of Grain Boundary Segregation on the Deformation Behavior of Nanocrystalline Ni50Co50 Solid Solution Alloys Investigated by Molecular Dynamics Simulations

Effects of SMAT Temperature and Stacking Fault Energy on the Mechanical Properties and Microstructure Evolution of Cu-Al-Zn Alloys

Segregation competition and complexion coexistence within a polycrystalline grain boundary network

Phase transformation from phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

Critical cooling rates for amorphous-to-ordered complexion transitions in Cu-rich nanocrystalline alloys

Deformation induced grain boundary segregation in nanolaminated Al–Cu alloy

Microstructure and Texture Evolution in Thermomechanically Processed FCC Metals and Alloys: a Review