Abstract:Improved mechanical properties of ferritic stainless steels (FSSs), such as toughness and high temperature or creep resistance, have been attained through the addition of stabilizing elements such as Nb and/or Ti. Therefore, stabilized ferritic stainless steels are good candidates to replace the conventional Cr-Ni austenitic stainless steels for specific applications to save the higher price of Ni. As compared to austenitic stainless steels, however, ferritic stainless steels possess lower formability which is closely depends on the gamma-fiber recrystallization texture. Hence, improvement of formability is desired for further wide applications of FSSs. The stabilizing effects of alloying elements work by consuming not only the interstitial atoms in solid solution but also forming the carbide and nitride precipitates such as TiC. TiN and NbC. The precipitation takes place in steel making processes such as slab reheating, hot rolling and coiling. The parameters involving these processes have their effects on the size, shape and distribution of the precipitates that influence the gamma-fiber recrystallization texture. Many papers intended to clarify the effect of precipitates. However, there were differences concerning the effect of precipitates, which may hinder further improvement of formability. In the present paper, precipitate size and dispersion were changed by controlling hot rolling processes and the effect of precipitate size and dispersion on the development of recrystallizaton texture in a 17%Cr ferritic stainless steels was investigated. Mechanical properties were measured by tensile tests. The characteristics of precipitate were observed by transmission electron microscopy, and X-ray diffraction was used to characterize texture evolution processes. The results show that low temperature finish rolling promotes the formation of a large number of fine and dispersed TiC precipitates in the hot band. After rolling and annealing, the state of fine and dispersed precipitation can be inherited in the cold rolled and annealed sheets. Strong gamma-fiber recrystallizaton texture is developed in the specimen with sparsely distributed and coarse precipitates. Fine and dispersed precipitates promote the nucleation of randomly oriented grains, strongly suppress the growth of recrystallized grain, and thereby weakening gamma-fiber recrystallizaton texture and impairing the formability of the cold rolled and annealed sheets. The precipitates have significant effects on the nucleation of randomly oriented grains and pinning grain boundary mobility during recrystallization annealing after cold rolling, which plays an important roles in controlling the gamma-fiber recrystallizaton texture in a ferritic stainless steels.

The effect of cold rolling reduction ratio on the microstructure and mechanical properties of ferritic stainless steel 430

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

An analysis of microstructure and mechanical properties of ferritic stainless steel 430 during cold rolling and subsequent annealing

Effect of Cold Rolling Reduction Rate on the Microstructure and Properties of Q&P Steel with a Ferrite-Pearlite Initial Structure

Effects of Hot Rolled Shear Bands on Formability and Surface Ridging of an Ultra Purified 21%cr Ferritic Stainless Steel

Effect of Cold Rolling Process on Microstructure, Texture and Formability of 00cr21monbti Ferritic Stainless Steel

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Formation of recrystallization texture and its effect on deep drawability for high-purified ferritic stainless steel by two step cold rolling

Improvement of Surface Ridging Resistance of an Ultra-purified Ferritic Stainless Steel by Optimizing Hot Rolling Condition

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Effect of the size and dispersion of precipitates formed in hot rolling on recrystallization texture in ferritic stainless steels

Cryorolling impacts on microstructure and mechanical properties of AISI 316 LN austenitic stainless steel

Effects of Cold Rolling on Intergranular Corrosion Resistance of 443 Ultra-Pure Ferritic Stainless Steel

Simultaneously Improving Mechanical Properties and Stress Corrosion Cracking Resistance of High-Strength Low-Alloy Steel via Finish Rolling within Non-recrystallization Temperature

Effect of cold drawing reduction rate on edge-to-center-characterized microstructure and orientation alongside residual stresses in conjunction with magnetic properties of low-carbon high-alloy ferromagnetic steel

Effects of Reduction Partitioning in Two-Stage Cold Rolling on the Surface Ridging Resistance of Ferritic Stainless Steel

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Microstructures and Mechanical Properties of Low Carbon Steel Hot Rolled in Ferrite Region Based on CSP Line

Development of Very Tough Ferritic Stainless Steels by Optimizing the Recrystallized Microstructure

Textures and Precipitates in A 17%cr Ferritic Stainless Steels