Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Simultaneously Improving Mechanical Properties and Stress Corrosion Cracking Resistance of High-Strength Low-Alloy Steel via Finish Rolling within Non-recrystallization Temperature

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Effect of Heavy Warm Rolling on Microstructures and Mechanical Properties of AISI 4140 Steel

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Enhanced mechanical properties of a Fe-Mn-Al-C austenitic low-density steel by increasing hot-rolling reduction

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Hot-Rolling and a Subsequent Direct-Quenching Process Enable Superior High-Cycle Fatigue Resistance in Ultra-High Strength Low Alloy Steels

Influence of warm rolling temperature on multi-scale lamellar structure and mechanical properties of medium carbon steel

Effects of rolling process on microstructure and mechanical properties of ultra high strength steel

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes

Effect of Annealing on Microstructure and Mechanical Properties of Ultrafine-Grained Low-Carbon Medium-Manganese Steel Produced by Heavy Warm Rolling

Low-Carbon Bainite Steel with High Strength and Toughness Processed by Recrystallization Controlled Rolling and Ultra Fast Cooling (RCR+UFC)

Effect of rolling temperature on microstructure evolution and mechanical properties of high carbon high manganese steel

Microstructure and mechanical properties of a low-carbon HDQ&P steel

Study of microstructures and deformation behavior of ultrafine-grained high-Mn TWIP steel fabricated by heavily asymmetric-symmetric rolling

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel