Abstract:The present report describes a technique in which the maxillary bone was molded to the desired location using a series of instruments for ridge-splitting procedures. This technique aims to improve bone quality all around the implants at both the crest and apex locations. In some clinical scenarios, insufficient horizontal bone with less than 3 mm prevents implant placement. Thus, ridge splitting is a treatment of choice, and this technique creates bone expansion to form a better receptor site for endosteal implants. A case report is presented involving a completely edentulous 52-year-old male patient presented to the clinic with a horizontal bone defect. The patient complained of having difficulty eating and wants to improve his smile. In this clinical case, a modified ridge-splitting technique was employed, differing from the conventional procedure that uses mallets, chisels, or osteotomes. A lancet and spatula were used for precise ridge splitting, followed by the placement of four endosseous tapered implants-two on each side (Dentis USA, La Palma, USA). Each implant had a diameter of 3.7 mm and a length of 10 mm. These implants were clinically placed in a single visit, with a torque of 30 N/cm² applied to ensure secure fixation. To accommodate the patient's unique maxillary bone anatomy, 25-degree angulated abutments were chosen for the four implants, ensuring a common path of insertion, and optimal angulation for long-term stability and aesthetics. Subsequently, a cemented provisional dental prosthesis restoration was fitted, and the patient reported satisfaction with both function and aesthetics. After a period of five months of osseointegration, the stability of the implants was assessed using a resonance frequency analyzer, yielding positive results. The average resonance frequency values for the maxillary left (canine and premolar) were ISQ 68 and ISQ 71, respectively, while for the maxillary right (lateral incisor and premolar), the values were ISQ 69 and ISQ 73. These readings indicate satisfactory implant stability following the osseointegration process. The postoperative cone-beam computed tomography (CBCT) showed gain to the bone width besides better function and good results concerning the esthetics. This report describes a modified ridge-splitting technique with a predictable and satisfactory outcome that fulfilled the patient's demands. The presented approach overcomes the disadvantages of two-staged implant placement bone grafting procedures and is also a more affordable option for the patient. CBCT evaluation confirmed bone gain with minimal morbidity after the procedure.

EVALUATION OF ONE-STAGE INVERTED U-SHAPED RIDGE SPLITTING AND CONCURRENT IMPLANT PLACEMENT IN ANTERIOR MAXILLARY UNDERCUT DEFECT(A CLINICAL TRIAL)

A Modified Ridge-Splitting Technique to Restore a Completely Edentulous Maxillary Arch With a Cement-Retained Implant Prosthesis

Apical U-shape Splitting Technique for Undercut Areas of the Anterior Alveolar Ridge: a Prospective Non-Randomized Controlled Study.

Clinical Use of Ridge-Splitting Combined with Ridge Expansion Osteotomy, Sandwich Bone Augmentation, and Simultaneous Implantation.

Assessment of vertical ridge augmentation and marginal bone loss using autogenous onlay vs inlay grafting techniques with simultaneous implant placement in the anterior maxillary esthetic zone: A randomized clinical trial

Maxillary Alveolar Ridge Expansion with Split-Crest Technique Compared with Lateral Ridge Augmentation with Autogenous Bone Block Graft: a Systematic Review

A three-in-one alveolar process reconstruction protocol for maxillary molar sites with severe residual bone height deficiency: A proof-of-concept pilot study

Mandibular Ridge Expansion Using a Horizontal Bone-Splitting Technique and Synthetic Bone Substitute: An Alternative to Bone Block Grafting?

Efficacy of laser biostimulation for mandibular narrow ridges treated with one-stage ridge splitting and two-implant overdentures: A one-year preliminary study

Ridge Expansion Alone or in Combination with Guided Bone Regeneration to Facilitate Implant Placement in Narrow Alveolar Ridges: a Retrospective Study

The Facial-Coronal Ridge Crest Alterations after Single Immediate Implant Placement and Provisionalization with Thin Buccal Plate Phenotype in Anterior Maxilla: A Radiographic Case-Series Study.

Ridge Augmentation and Concomitant Implant Placement in the Esthetic Zone Through One Surgical Site: A Clinical Report

[Evaluation of Alveolar Ridge Reconstruction and Esthetic Result Following Immediate Implant].

Alveolar ridge preservation in defect sockets in the maxillary aesthetic zone followed by single-tooth bone level tapered implants with immediate provisionalization: a 1-year prospective case series

Modified 3-Dimensional Alveolar Ridge Augmentation in the Anterior Maxilla: A Prospective Clinical Feasibility Study

Immediate implant placement combined with maxillary sinus floor elevation utilizing the transalveolar approach and nonsubmerged healing for failing teeth in the maxillary molar area: A randomized controlled trial clinical study with one-year follow-up

A modified crestal ridge expansion technique for immediate placement of implants: a report of three cases

Alveolar ridge augmentation using autogenous bone graft and platelet-rich fibrin to facilitate implant placement

[Clinical Effects of Ridge Augmentation with the Half-Columnar Shaped Mandibular Bone Block for the Placement of Dental Implants].

Immediate Implant Placement with Buccal Bone Augmentation in the Anterior Maxilla with Thin Buccal Plate: A One-Year Follow-Up Case Series.

Mineralized Plasmatic Matrix in Ridge Preservation: A Randomized Controlled Clinical Trial