Abstract:Powder Metallurgy route was employed to produce high entropy alloys Co–Cr–Ni-Mn–Fe–SiC x where x indicates the weight percentage of SiC. This investigation shows the different proportion of SiC content ( x = 2 wt.%, 4 wt.% and 6 wt.%) added in Co–Cr–Ni-Mn–Fe– powders. The trial samples were compacted using a press and subjected to sintering at two distinct temperatures ( T sint ) 1250° and 1350 °C respectively.T he composites were subjected to characterization technique such as optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and atomic force microscopy. These HEA alloys were analyzed for the distribution of SiC in HEA matrix using SEM and it was observed that the distribution of SiC was homogeneous, as shown in the matrix. The synthesized SiC reinforced composites are subjected to compression test, hardness test and corrosion test. The densification behavior was examined on the sintered specimens. The post sintering process study indicates that the density of HEA- 0 wt.% SiC, HEA-2 wt.% SiC, HEA- 4 wt.% SiC, and HEA-6 wt.% SiC composites, which was sintered at 1350 °C, are 7.38, 7.05, 6.73 and 6.41, respectively. Co–Cr–Ni-Mn–Fe HEA alloys sintered at 1350 °C have density of 0.66% greater than alloys sintered at 1250 °C.Co–Cr–Ni-Mn–Fe-4 wt.% SiC alloy sintered at 1350 °C and the properties like compression strength, corrosion resistance and hardness are found to be very high. Unreinforced Co–Cr–Ni-Mn–Fe alloy sintered at 1350 °C exhibits sinterability of 0.89.Among the composites sintered at 1250 °C and 1350 °C, Co–Cr–Ni-Mn–Fe-2 wt.% SiC exhibit highest sinterability of 0.81. The ball milled powder morphology was analyzed using SEM and elemental presence of Cr, Co, Mn, Ni, Fe, and SiCin the matrix was confirmed and verified by the energy dispersive spectroscopy (EDS) analysis. The HEA composite (Co–Cr–Ni-Mn–Fe- 4 wt.% SiC composite) sintered at 1350 °C exhibits the best corrosion resistance which was determined by the potentiodynamic investigation.

Exploring strengthening mechanism of FeCoNiAl high-entropy alloy by non-metallic silicon addition produced via powder metallurgy

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Microstructural Evolution and Mechanical Properties of Al0.3CoCrFeNiSix. High-Entropy Alloys Containing Coherent Nanometer-Scaled Precipitates

Influences of Si and C addition on microstructure and mechanical properties of Fe2.5CoNiCu high-entropy alloy

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Effect of Si alloying on the structural, thermal expansion, and magnetic properties of FeCoNiAlSix high-entropy alloys

Multiscale-phase-driven strength-ductility synergy in Fe3Cr2CoNiAlx high entropy alloys

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Microstructure and mechanical properties of Fe50Mn30Co10Cr10 high-entropy alloy with Si addition prepared by laser melting deposition

Effects of Co/Ni ratio on microstructure and mechanical properties of as-cast Cr-Fe-Ni-Co-Al-Si-Ti-Cu high entropy alloys

Tuning the microstructure and strengthening mechanism of the CoCrFeNi high-entropy alloy via doping metalloid and interstitial elements

Microstructure and tensile properties of Co-free Fe4CrNi(AlTi) high-entropy alloys

Investigations on Silicon Carbide Reinforced High Entropy Alloy (CoCrNiMnFe) matrix Composites Produced by Powder Metallurgy Process

Magnetic and mechanical properties of nanotwin SiO 2 -FeCoNi(AlSi) 0.4 high entropy alloy prepared by mechanical alloying and spark plasma sintering

(FeCoNi)75Cu25-xSix high entropy alloys prepared by mechanical alloying and spark plasma sintering: Microstructure, deformation behavior and dynamic recrystallization kinetics

Evaluation of the impact of Mn and Al on the microstructure of Fe–Co–Ni–Cr based high entropy alloys

Electron beam melting of (FeCoNi)86Al7Ti7 high-entropy alloy

Realizing strength-ductility combination of Fe3.5Ni3.5Cr2MnAl0.7 high-entropy alloy via coherent dual-phase structure

Unveiling the Effect of Si on the Microstructure and Properties of AlFeCoCrNi High Entropy Alloy Coating