Abstract:Solid-state lithium (Li) metal batteries are widely used due to their excellent safety, superior energy density, and low cost. Nevertheless, the practical application of solid-state Li batteries is hindered by the inferior ionic conductivity of the solid electrolyte and poor interface contact between the electrode and electrolyte. Herein, a flexible, hybrid ceramic-based electrolyte was fabricated by a solution-casting method using poly(vinylidene fluoride), Li1.4Al0.4Ti1.6(PO4)3 powders, and lithium bis(trifluoromethanesulfonyl)imide. To realize high ionic conductivity and a stable self-viscous electrode/electrolyte interfacial contact simultaneously, a mixed solution of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, lithium bis(trifluoromethanesulfonyl)imide, and fluoroethylene carbonate was introduced by the solution-infiltration method. The self-viscous Li1.4Al0.4Ti1.6(PO4)3 ceramic-based electrolyte exhibits superior ionic conductivity (2.4 × 10–4 S cm–1 at 25 °C), a high ionic transference number (0.42), wide voltage window (4.8 V vs Li/Li+), excellent thermal stabilities, and the ability to impede Li dendrite growth. In particular, the stable contact, low interfacial resistance, and fast ion-transport channels between the electrodes and solid electrolytes can be achieved by the self-viscous interfacial layer. The solid-state LiFePO4|Li battery assembled with the solid self-viscous electrolyte demonstrates a satisfactory initial discharge capacity of 138.0 mAh g–1 and capacity retention of 96.5% after 200 cycles at 0.5 C and under 25 °C. The self-viscous modification strategy of the solid electrolyte affords promising options for implementing the intimate electrode/electrolyte interfacial contact in high-energy-density solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.energyfuels.1c01202.Figure S1: XRD patterns and SEM image of LATP ceramic powders. Figure S2: Temperature dependence of ionic conductivities for LATP pellets. Figure S3: Flexible and winding performances of self-viscous PLL-LEF electrolyte. Figure S4: Surface morphology of PL and PLL-LEF electrolytes. Figure S5: Adhesiveness exhibitions of PLL-LE composite electrolyte. Figure S6: EIS profiles of 10LiTFSI-40EMITFSI and 10LiTFSI-40EMITFSI-10FEC electrolytes. Figure S7: EIS profiles of stainless steel|PLL-LEF|Li cells. Figure S8: Thermogravimetry curve of PLL-LEF electrolyte. Figure S9: Flammability test of routine Celgard separator. Figure S10: EIS profiles of Li|PLL|Li cell for different aging times. Figure S11: Optical photographs of the PLL electrolyte. Figure S12: Ti 2p XPS of the PLL electrolyte. Figure S13: EIS profiles of Li symmetric cell with different electrolytes after cycling. Figure S14: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.2 mA·cm–2. Figure S15: Constant current cycling curves of Li|PLL-LEF|Li cells at 0.5 mA·cm–2. Figure S16: Constant current cycling curves of Li|PLL-LEF|Li cells. Figure S17: High multiple SEM images of Li surfaces obtained from Li symmetrical cells. Figure S18: SEM image of pristine Li surface. Figure S19: EIS results of LiFePO4|PLL|Li, LiFePO4|PLL-LE|Li and LiFePO4|PLL-LEF|Li batteries. Figure S20: Typical charge–discharge voltage profiles of LiFePO4|PLL-LE|Li cell at 0.5 C. Figure S21: Electrochemical properties of Al2O3@LiNi0.5Co0.3Mn0.3O2|PLL-LEF|Li cell (PDF)This article has not yet been cited by other publications.

Solvent-Free and Long-Cycling Garnet-Based Lithium-Metal Batteries

PEO/garnet Composite Electrolytes for Solid-State Lithium Batteries: from “Ceramic-in-polymer” to “Polymer-in-ceramic”

A High-Performance, Solution-Processable Polymer/ceramic/ionic Liquid Electrolyte for Room Temperature Solid-State Li Metal Batteries

Molten Salt Driven Conversion Reaction Enabling Lithiophilic and Air‐Stable Garnet Surface for Solid‐State Lithium Batteries

Enhanced Cathode/Electrolyte Interface in Solid-state Li-metal Battery based on Garnet-type Electrolyte

Garnet-based solid lithium metal batteries with ultralong lifespan enabled by solvent-free trifluoroacetic acid-induced interfacial engineering

Versatile Inorganic/Polymer Composite Electrolyte Added with 2-Methylsuccinic Anhydride via a Solvent-Free Preparation Method for High-Performance All-Solid-State Li-Metal Batteries: High Voltage, Long Cycle Life, and Room-Temperature Operation

Stabilize Garnet/Electrode Interface via Low-melting Polymer Layer in Solid-state Lithium Metal Battery

Stable Interface Chemistry and Multiple Ion Transport of Composite Electrolyte Contribute to Ultra‐long Cycling Solid‐State LiNi0.8Co0.1Mn0.1O2/Lithium Metal Batteries

Solvent‐Free Synthesis of Thin, Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Stabilizing Ceramic-Based Electrolyte Interfaces with Self-Viscous Modification Strategy for Solid-State Lithium Batteries

Highly stable garnet solid electrolyte based Li-S battery with modified anodic and cathodic interfaces

A Long Cycle Life, All-Solid-State Lithium Battery with a Ceramic–Polymer Composite Electrolyte

High-performance lithium metal batteries enabled by a nano-sized garnet solid-state electrolyte modified separator

Solid-State Li-Ion Batteries Using Fast, Stable, Glassy Nanocomposite Electrolytes for Good Safety and Long Cycle-Life

Synergistically enabling the interface stability of lithium metal batteries with soft ionic gel and garnet-type Li6.4La3Zr1.4Ta0.6O12 ceramic filler

Composite solid electrolytes containing single-ion lithium polymer grafted garnet for dendrite-free, long-life all-solid-state lithium metal batteries

In Situ Solidified Gel Polymer Electrolytes for Stable Solid−State Lithium Batteries at High Temperatures

Air-stable and Lithium-compatible Garnet Pellet Enabled by Surface Doping for High Performance Solid-state Batteries

Unlocking the concentration polarization for Solid-State lithium metal batteries

Intercalated Electrolyte with High Transference Number for Dendrite‐Free Solid‐State Lithium Batteries