Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Synthesis and Electrochemical Performance of Microporous Hollow Carbon from Milkweed Pappus as Cathode Material of Lithium–Sulfur Batteries

Carbonized Waste Milk Powders As Cathodes for Stable Lithium-Sulfur Batteries with Ultra-Large Capacity and High Initial Coulombic Efficiency

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Evolution of Hollow N‐Doped Mesoporous Carbon Microspheres from Outdated Milk As Sulfur Cathodes for Lithium‐Sulfur Batteries

Hierarchically Structured Sulfur/Carbon Nanocomposite Material for High-Energy Lithium Battery

Clustered-Microcapsule-Shaped Microporous Carbon-Coated Sulfur Composite Synthesized Via in Situ Oxidation.

Biomass-Derived Porous Carbon with Micropores and Small Mesopores for High-Performance Lithium-Sulfur Batteries

Green and Highly-Efficient Microwave Synthesis Route for Sulfur/Carbon Composite for Li-S Battery

Activated Carbon with Ultrahigh Specific Surface Area Synthesized from Natural Plant Material for Lithium–sulfur Batteries

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

Preparation of Mesohollow and Microporous Carbon Nanofiber and Its Application in Cathode Material for Lithium–sulfur Batteries

Mesoporous carbon-carbon nanotube-sulfur composite microspheres for high-areal-capacity lithium-sulfur battery cathodes.

Natural Biomass-Derived Porous Carbon from Water Hyacinth Used as Composite Cathode for Lithium Sulfur Batteries

Hierarchical Porous Carbon Materials Derived from Self-Template Bamboo Leaves for Lithium–Sulfur Batteries

A hierarchical micro/mesoporous carbon fiber/sulfur composite for high-performance lithium-sulfur batteries

A wheat flour derived hierarchical porous carbon/graphitic carbon nitride composite for high-performance lithium–sulfur batteries

Construction of tubular polypyrrole-wrapped biomass-derived carbon nanospheres as cathode materials for lithium–sulfur batteries

Biomass Waste Inspired Highly Porous Carbon for High Performance Lithium/Sulfur Batteries

Enhanced performance of lithium-sulfur battery cathode via composition optimization using modified MWCNTs as a conductive material and poly (acrylic acid) as a binder

A Mixed Microporous/Low-range Mesoporous Composite with High Sulfur Loading from Hierarchically-structured Carbon for Lithium Sulfur Batteries

Green biomass-derived hierarchically porous non-activated carbon from carob waste for high-performance lithium-sulfur batteries