Abstract:Developing a high-strength, flame-resistant structural material derived from wood is desirable for advanced applications in the transportation, construction, automotive, and aerospace sectors. Here, a low-cost and high-efficiency top-down method was designed for processing natural wood veneers into lightweight yet strong bulk structural wood-based composites. The composites were produced using delignified wood veneers as a continuous reinforcing material and epoxy resin as the adhesive, followed by hot pressing. Densification of the veneers and good adhesion among the veneers played a pivotal role in the mechanical performance of the composites. A record-high flexural strength of 436.1 MPa and a toughness of 12.3 MJ·m–3 were achieved. Furthermore, the low density of the wood composite led to a specific flexural strength of 323.0 MPa·cm3·g–1, which is significantly greater than those reported for other wood-based composites and some metal materials (e.g., steels and alloys). We also explored the feasibility of using the composite in unmanned drones. In addition, the delignified wood veneers were infiltrated with 1.5% ammonium polyphosphate (APP), which improved the fire-retardant and self-extinguishing properties of the composites. This work demonstrates that high-strength wood products exhibit significant potential in many applications.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acssuschemeng.0c09390.Molding process of DWLC-41.4% with different shapes (Figure S1); delignified wood panels with different lignin removal contents (Figure S2); thickness swelling (24 h) (Figure S3); SEM images of DWLC-0%, DWLC-23.2%, and DWLC-55.1% (Figure S4); micro-CT images (Figure S5); tensile and flexural strength of DWLC-41.4% with and without epoxy resin (Figure S6); photographs of wood veneer pull-out tests: before (left) and after (right) (Figure S7); bonding strength of wood veneer and epoxy resin (Figure S8); microstructure of fracture surfaces of pure epoxy resin (Figure S9); compressive strength of natural birch wood and DWLC-41.4% (Figure S10); mechanical properties and microstructures of DWLCs with and without flame retardant (Figure S11); TG curves of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC (Figure S12); mass loss of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC after the cone test (Figure S13); TSR curves of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC (Figure S14); XPS spectra of P of 1.5% APP/DWLC and 2.5% APP/DWLC (Figure S15); comparison of TTI between DWLC-41.4% and other wood-based composites (Table S1); and XPS analysis of the external char of DWLC-41.4% with and without flame retardant (Table S2) (PDF)Takeoff process of an unmanned drone (Movie S1) (MP4)This article has not yet been cited by other publications.

Reengineering Wood into a High-Strength, and Light-Weight Bio-Composite Material for Structural Applications

Lightweight, High-Strength Wood Prepared by Deep Eutectic Solvent Treatment as a Green Structural Material

Laminating Delignified Wood Veneers toward High-Strength, Flame-Retardant Composites for Structural Applications

High-Performance All-Bio-Based Laminates Derived from Delignified Wood

Preparation and Closed-Loop Recycling of Ultra-High-Filled Wood Flour/Dynamic Polyurethane Composites

Exploring strategies for valorizing wood processing waste: advancing sustainable, fully lignocellulosic biocomposites

Epoxy-Acrylic Polymer In-Situ Filling Cell Lumen and Bonding Cell Wall for Wood Reinforcement and Stabilization

Sustainable Engineering Polymer Composites Fabricated Using Delignified Bamboo Fiber as Reinforcement and Walnut Shell Powder as Filler

A novel sol-gel strategy for constructing wood fibers and aramid nanofiber nanocomposite with strong, tough and recyclable properties

High-performance Self-Bonding Bio-Composites from Wood Fibers

Glueless formaldehyde-free biocomposites with high strength based on the three-dimensional structure of wood fibres

Green and sustainable fabrication of DES-pretreated high-strength densified wood

Scalable high-performance wood-based composites prepared by hydro-mechanical treatment

Fabrication and Design of Wood-Based High-Performance Composites

Processing bulk natural wood into a high-performance structural material

Bio-based composites fabricated from wood fibers through self-bonding technology

An effective technique for constructing wood composite with superior dimensional stability

Synergistic in-situ reinforcement of lignin and adhesive for high-performance aligned bamboo fibers composites

Wood-Based Nanocomposite Derived by in Situ Formation of Organic-Inorganic Hybrid Polymer within Wood via a Sol-Gel Method.

All-natural bioinspired nanolignocellulose-derived bulk engineering materials with excellent mechanical properties and environmental stability

A novel wood fiber/waterborne epoxy resin composite with high fiber content and performance fabricated by a green and simple process