Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

A fast-setting and eco-friendly superhydrophobic high belite sulphoaluminate cement mortar

An eco-friendly and low-cost superhydrophobic alkali-activated Portland slag cement mortar

Fabricating hydrophobic silica fume to improve mechanical strength and anti-corrosion of integral hydrophobic cement mortar

Permeabilities and Mechanical Properties of Hardened Cement Pastes Modified with Sodium Laurate and Nano Silica

Mechanical properties and hydration of ultra-high-performance seawater sea-sand concrete (UHPSSC) with limestone calcined clay cement (LC3)

SYNTHESIS AND CHARACTERIZATION OF HIGH BELITE SULFOALUMINATE CEMENT THROUGH RICH ALUMINA FLY ASH AND DESULFURIZATION GYPSUM

Green Fabrication of Superhydrophobic Zeolite Coating on Cement-Based Material Surfaces to Improve Water-Resistant and Anticorrosion Properties

Design of monolithic superhydrophobic concrete with excellent anti-corrosion and self-cleaning properties

Effect of calcium sulfate type and dosage on the properties of high-belite sulfoaluminate cement

Superhydrophobic concrete coating with excellent mechanical robustness and anti-corrosion performances

Effect of organic alkali on hydration of GGBS-FA blended cementitious material activated by sodium carbonate

Research on the Performance of Superhydrophobic Cement-Based Materials Based on Composite Hydrophobic Agents

Strengthening effect of sulphoaluminate cementitious grouting material for water-bearing broken rocky stratum

Study of Salt Resistance and Mechanical Strength of Robust and Non-Fluorinated Superhydrophobic Cement

Study on the anti-corrosion properties of hydrophobic cement mortar containing coral sand

Sulphate Corrosion Mechanism of Ultra-High-Performance Concrete (UHPC) Prepared with Seawater and Sea Sand

Abundant octadecylamine modified epoxy resin for superhydrophobic and durable composite coating

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Development of High-Performance Microfine Cementitious Grout with High Amount of Fly Ash, Silica Fume, and Slag

Mechanical properties and hydration mechanism of super-sulfated cement prepared with ordinary Portland cement, carbide slag, and sodium silicate

Study on the Corrosion Resistance of Hydrophobic Cement Mortar