Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Evolution behavior and mechanism of iron carbon agglomerates under simulated blast furnace smelting conditions

Non-isothermal Reduction Process Analysis of Iron-Bearing Burden with Charging Iron Coke Hot Briquette under Simulated Blast Furnace Conditions

Evolution Characteristics and Influence Mechanism of Binder Addition on Metallurgical Properties of Iron Carbon Agglomerates

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Relationship and Mechanism Analysis of Soft-Melt Dropping Properties and Primary-Slag Formation Behaviors of the Mixed Burden in Increasing Lump Ore Ratio

Effect of Titanomagnetite Ironsand Coal Composite Hot Briquette on Softening-melting Performance of Mixed Burden under Simulated Blast Furnace Conditions

Effects of Coal and Iron Ore Blending on Metallurgical Properties of Iron Coke Hot Briquette

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Experimental Study on Impact of Iron Coke Hot Briquette As an Alternative Fuel on Isothermal Reduction of Pellets under Simulated Blast Furnace Conditions

Influence of Iron Ore Addition on Metallurgical Reaction Behavior of Iron Coke Hot Briquette

Interfacial reaction behavior in blast furnace and analysis of influence mechanism

Computational Study of Hot Gas Injection (HGI) into an Ironmaking Blast Furnace (BF)

Evaluating the Effect of MgO/Al2O3 Ratio on Thermal Behaviors and Structures of Blast Furnace Slag with Low Carbon Consumption

Computational Fluid Dynamics Study of the Flow and Thermochemical Behaviors of a Carbon Composite Briquette in an Ironmaking Blast Furnace

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

Computational Fluid Dynamics Study of the Thermochemical Behaviors in an Ironmaking Blast Furnace with Oxygen Enrichment Operation

Melting–Dropping Property of Blast Furnace Charge on the Basis of its Slag Formation Behavior

Effect of Iron CoKe Hot Briquette on Softening-Melting and Dripping Properties of Blast Furnace Mixed Burden

A Novel Technique for the Preparation of Iron Carbide and Carbon Concentrate from Blast Furnace Dust

Experimental Study on the Resource Utilization of Carbide Slag in Iron Ore Sintering Process

Effect of Ore Type and Gangue Content on Carburization and Melting Behavior of Carbon-Iron Ore Composite