Abstract:In order to reduce current leakage and improve electron transfer in solar cells, charge transport layers (CTL), mainly hybrid electron transport layers (h-ETL), are considered as a solution. In this research contribution, computational analysis using SCAPS-1D software is performed to explore the output photovoltaic parameters of a Sb2S3-based solar cell with h-ETL. No theoretical works on this configuration have been previously reported. The main objectives of the present work are to propose a h-ETL with good band alignment with the Sb2S3 absorber, high transparency, and Cd free; to mitigate the instability and cost issues associated with using Spiro-OMeTAD HTL; and to optimize the solar cell. Thus, we calibrated the J - V characteristics and electrical parameters of the FTO/(ZnO/TiO2)/Sb2S3/Spiro-OMeTAD/Au solar cell by numerical simulation and compared them with those of the experiment. Subsequently, our simulations show that to replace the TiO2 ETL used in the experiment and to form the h-ETL with ZnO, IGZO is found to be a good candidate. It has better band alignment with the Sb2S3 absorber than TiO2 ETL, which reduces the trap states at the ETL/Sb2S3 interface; it has high transparency due to its wide bandgap; and an intense electric field is generated at the IGZO/Sb2S3 interface, which reduces the recombination phenomenon at this interface. MoO3, MASnBr3, Cu2O, CuI, and CuSCN HTL were also tested to replace the Spiro-OMeTAD HTL. Simulation results show that the cell with MoO3 HTL achieves higher performance due to its high hole mobility and high quantum efficiency in the visible region; it also allows the solar cell to have better thermal stability ( TC = − 0.32 %/K) than the cell with Spiro-OMeTAD HTL ( TC = − 0.53 %/K). The parameters that could improve the solar cell efficiency ( η ) obtained after these substitutions were also optimized. In particular, the parameters of the Sb2S3 absorber layer (thickness, defect density, and doping), ETL and HTL layer thicknesses, h-ETL/Sb2S3 interface defect density, and series and shunt resistances have been optimized. Finally, by combining high performance and thermal stability, the results show that the thermal stability of the solar cell depends on the back contact type; thus, nickel (Ni) was found to combine high performance and better thermal stability among the back contacts investigated. After these improvements, the efficiency of the Sb2S3-based solar cell increased from 5.08% ( J SC = 16.19 mA/cm2, V OC = 0.56 V, and FF = 55.40 %) to 15.43% ( J SC = 18.51 mA/cm2, V OC = 1.11 V, and FF = 74.76 %). This study proposes an approach to optimize the Sb2S3 upper subcell for tandem solar cells.

Design and Simulation of Efficient SnS-Based Solar Cell Using Spiro-OMeTAD as Hole Transport Layer

Metal Organic Framework Doped Spiro-OMeTAD with Increased Conductivity for Improving Perovskite Solar Cell Performance

Investigating the Performance of Lead-Free Perovskite Solar Cells Using Various Hole Transport Material by Numerical Simulation

Modeling and Simulation of Tin Sulfide (SnS)-Based Solar Cell Using ZnO as Transparent Conductive Oxide (TCO) and NiO as Hole Transport Layer (HTL)

Investigation of the Performance of a Sb2S3-Based Solar Cell with a Hybrid Electron Transport Layer (h-ETL): A Simulation Approach Using SCAPS-1D Software

Examining Compatible Electron Transport Layers for CsSnBr3‐Based Solar Cell to Boost Photovoltaic Stability and Efficiency

Effect of Different Device Parameters on Tin Based Perovskite Solar Cell Coupled with In2S3 Electron Transport Layer and CuSCN and Spiro-OMeTAD Alternative Hole Transport Layers for High Efficiency Performance

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement

Amorphous-conjugated polymer-additive approach to prepare quality Spiro-OMeTAD-based hole transporting material for efficient Sb2S3 solar cells

Design of Low Crystallinity Spiro-Typed Hole Transporting Material for Planar Perovskite Solar Cells to Achieve 21.76% Efficiency

Performance Enhancement of SnS Solar Cell with Tungsten Disulfide Electron Transport Layer and Molybdenum Trioxide Hole Transport Layer

Comparative Analysis and Performance Optimization of Low-Cost Solution-Processed Hybrid Perovskite-Based Solar Cells With Different Organic HTLs

Simulating the Effect of Inserting Sb2S3 as Hole Transport Layer on SnS-Based Thin-Film Solar Cells

Demethylation strategies for spiro-OMeTAD to enhance the thermo-opto-electronic properties as potential hole transport materials in perovskite solar cells

Modeling and Simulation of MAPbI3-Based Solar Cells with SnS2 As the Electron Transport Layer (ETL) and MoS2 As the Hole Transport Layer (HTL)

Design and simulation of Cu2SnSe3-based solar cells using various hole transport layer (HTL) for Performance Efficiency above 32%

Simulation and modeling of a new CsSnI3 solar cell structure: A numerical study

TD-DFT-guided development of a robust hole-transporting layer for optimized triple-cation perovskite solar cell performance

CuGaO<sub>2</sub> Nanosheets and CuCrO<sub>2</sub> Nanoparticles Mixed with Spiro-OMeTAD as the Hole-Transport Layer in Perovskite Solar Cells

NiOx/Spiro Hole Transport Bilayers for Stable Perovskite Solar Cells with Efficiency Exceeding 21%

SCAPS 1D based study of hole and electron transfer layers to improve MoS2−ZrS2 solar cell efficiency