Abstract:In order to improve the full utilization of wheat straw, to enhance the mechanical properties of gypsum board and to increase the fire resistance of wood-based gypsum board, a new preparation process of gypsum-based composites with wheat straw was put forward in this study. The thick and small wheat straw fiber were used as the reinforcing materials in gypsum-based composites, and their dimension were in the range of 0.30-0.60 and 0.18-0.30 mm, respectively. The gypsum was employed as the continuous phase in the composites. The ambient temperature curing structural adhesive was used to replace the traditional gypsum retarder in the new preparation process of gypsum-based composites. The preparation process consisted of an initial forming stage for initial strength and a curing stage, where the objectives were gypsum hydration and the strength further increased, respectively. Compared with the conventional gypsum composites with Chinese fir fiber and Chinese fir particle, the mechanical properties and fire resistance of gypsum-based composites by adding wheat straw fiber with different dimension were tested and analyzed. The results showed that the physical and mechanical properties of gypsum-based composites with small wheat straw fiber were lower than those of gypsum-based composites with Chinese fir fiber, but were better than gypsum-based composites with thick wheat straw fiber. The internal bond strength, modulus of rupture, modulus of elasticity and thickness swelling of gypsum-based composites with small wheat straw fiber were 0.33 MPa, 7.1 MPa, 2 370 MPa and 2.82%, respectively, and could meet the requirements of gypsum particleboard standard. According to the lower thermal conductivity and higher ash content of wheat straw than wood materials, the time to ignition of gypsum-based composites with wheat straw was higher than that of gypsum-based composites with Chinese fir fiber, and there was no obvious peak heat release rate in the fire resistance test. Compared with the gypsum-based with Chinese fir fiber and Chinese fir particle, the total heat release of gypsum-based composites with small wheat straw fiber was 48.18% and 35.87% lower, respectively. The main peak of CO2 production rate was 42.25% and 38.81% lower than that of Chinese fir fiber and particle gypsum composites, respectively. The main peak of CO production rate was comparable to wood-gypsum composites. The weight percent retains of small wheat straw fiber gypsum composites was slightly higher than that of Chinese fir gypsum composites, and the appearance after burning test was more complete and the degree of carbonization was lighter obviously. Due to the smooth outer surface of the wheat straw, the gypsum was mainly attached to the internal surface of the wheat straw by microscopic observation using scanning electron microscope. Therefore, the small straw fiber could increase the contact area between the internal surface and the gypsum, which indicated the inherent reason for the better physical and mechanical properties of small wheat straw fiber gypsum composites. The smooth outer surface of the wheat straw was almost covered with SiO2, which also explained the superior fire resistance of wheat straw gypsum composites. The study can be a reference for the performance improving on the gypsum-based composites with wheat straw fiber and its application in project.

Graphene-based nano-functional materials for surface modification of wheat straw to enhance the performance of bio-based polylactic acid composites

Improved properties of PLA biocomposites toughened with bamboo cellulose nanowhiskers through silane modification

PLA toughened by bamboo cellulose nanowhiskers: Role of silane compatibilization on the PLA bionanocomposite properties

High-toughness PLA/Bamboo Cellulose Nanowhiskers Bionanocomposite, Strengthened with Silylated Ultrafine Bamboo-Char

Effects of Bamboo Cellulose Nanowhisker Content on the Morphology, Crystallization, Mechanical, and Thermal Properties of PLA Matrix Biocomposites

Conversion from Bamboo Waste Derived Biochar to Cleaner Composites: Synergistic Effects of Aramid Fiber and Silica

Sustainable packaging biocomposites from polylactic acid and wheat straw: Enhanced physical performance by solid state shear milling process

Nano-TiO2 Modified Wheat Straw/Polylactic Acid Composites Based on Synergistic Effect Between Interfacial Bridging and Heterogeneous Nucleation

A Compatible Interface of Wheat Straw/Polylactic Acid Composites Collaborative Constructed Using KH570–Nano TiO2

Effects of organically-modified montmorillonite and alkalinization on physical, mechanical, chemical, morphological, and thermal properties of wheat straw/recycled polypropylene nanocomposites

Effect of silane coupling agent on compatibility interface and properties of wheat straw/polylactic acid composites

Effect of Chemical Treatment on Rice Straw Fiber Surface and Properties of Straw/Polylactic Acid Composites

Influence of carboxy-terminated hyperbranched polyester and polyethylene glycol on the mechanical and thermal properties of polylactic acid/straw flour composites

Preparation and characterization of poly (lactic acid) (PLA)/polyamide 6 (PA6)/graphene nanoplatelet (GNP) blends bio-based nanocomposites

Bio-based Green Composites with High Performance from Poly(lactic Acid) and Surface-Modified Microcrystalline Cellulose

Synergistic modification of polylactic acid by oxidized straw fibers and degradable elastomers: A green composite with good strength and toughness

Synergistic preparation of a straw fiber/polylactic acid composite with high toughness and strength through interfacial compatibility enhancement and elastomer toughening

Preparation and Optimization of Chemically Modified Corn Straw/Chitosan/PLA Composite Using RSM

Mechanical properties and fire resistance of gypsum-based composites with wheat straw

Tailoring interfacial adhesion and mechanical performance of biocomposites based on poly(lactic acid)/rice straw by using maleic anhydride through reactive extrusion process

Electrical and Thermal Conductivity of Polylactic Acid (PLA)-Based Biocomposites by Incorporation of Nano-Graphite Fabricated with Fused Deposition Modeling