Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

Optimization of wear and cracks in roller contact under different coating and a range of loads and temperature with fixed speed using design expert (DOE) and finite element model

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Numerical Study of the Thermodynamic Behavior and Wear on the Surface of Hot-Rolling Descaling Roll

Failure Analysis of a Working Roll under the Influence of the Stress Field Due to Hot Rolling Process

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Wear parameter optimization for CrN/TiAlSiN coating using novel BWM integrated TODIM decision-making approach

Optimisation of dry sliding wear characterisation of as-cast and T6 treated hypereutectic aluminium alloy (AlSiCuCe) by Taguchi technique

Numerical Analysis and Parameter Optimization of Wear Characteristics of Titanium Alloy Cross Wedge Rolling Die

Tribological Investigation of Composite MoS2-TiO2-ZrO2 Coating Material by Response Surface Methodology Approach

Prediction of Surface Wrinkle Defect of Welding Wire Steel ER70S-6 in Hot Bar Rolling Process Using Finite Element Method and Experiments

Stress Intensity Factor Evaluation for Fatigue Crack in Working Roll Due to Hot Rolling Process

Enhanced Fracture Toughness of WC-CoCr Thermally Sprayed Coatings by the Addition of NiCrFeSiBC and Mo and Its Influence on Sliding Wear Behavior

Experimental study and numerical simulation of iron oxide scales mechanical behavior in hot rolling

Experimental Method of Tribological Modelling of Different Coatings of Stainless Steel

Experimental Analysis and Modelling for Reciprocating Wear Behaviour of Nanocomposite Coatings

The Role of Oxide-Scale Microtexture on Tribological Behaviour in the Nanoparticle Lubrication of Hot Rolling

Assessment of the Impact of Wear of the Working Surface of Rolls on the Reduction of Energy and Environmental Demand for the Production of Flat Products: Methodological Approach

Rolls wear characterization in hot rolling process

Analysis and design optimization of double-sided deep cold rolling process of a Ti-6Al-4V blade

Theoretical Analysis and Numerical Simulation of External Spline Cold Rolling

A novel method for competitive failure behavior and mechanical degradation online monitoring of laser additive work roll under multidimensional damage