Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

Rolls wear characterization in hot rolling process

Experimental study and numerical simulation of iron oxide scales mechanical behavior in hot rolling

Numerical Study of the Thermodynamic Behavior and Wear on the Surface of Hot-Rolling Descaling Roll

Initiation of Sticking during Hot Rolling of Stainless Steel Plate

Effect of hot rolling process parameters on surface wear of descaling rolls

Effects of surface preparation on tribological behaviour of a ferritic stainless steel in hot rolling

Assessment of the Impact of Wear of the Working Surface of Rolls on the Reduction of Energy and Environmental Demand for the Production of Flat Products: Methodological Approach

The effect of oxide scale of stainless steels on friction and surface roughness in hot rolling

STUDY ON ROLL WEAR ON HOT STRIP ROLLING MILL

Oxide scale characterization of ferritic stainless steel and its deformation and friction in hot rolling

Characterization of the Microstructure Changes Induced by a Rolling Contact Bench Reproducing Wheel/Rail Contact on a Pearlitic Steel

The production and formal control of sulphide inclusions in steel

Mechanism of Oxidation of Austenitic Stainless Steels under Conditions of Hot Rolling in Steckel Mills

ROLL WEAR ON FINISHING TRAIN OF 2050 CVC HOT STRIP MILL

Surface texture transfer in skin-pass rolling with the effect of roll surface wear

New Tribological Aspects in the Micro-Areas of the Symmetric Rolling-Sliding Contact

Investigation of oxide scale on ferritic stainless steel B445J1M and its tribological effect in hot rolling

The Role of Oxide-Scale Microtexture on Tribological Behaviour in the Nanoparticle Lubrication of Hot Rolling

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Factors Affecting the Development of Oxide Scales on Austenitic Stainless Steels during Hot Rolling in Steckel Mills

Dry Sliding Friction of Tool Steels and Their Comparison of Wear in Contact with ZrO2 and X46Cr13