Abstract:Additive manufacturing (AM) is becoming increasingly popular since it offers flexibility to produce complex designs with less tooling and minimum material at shorter lead times. Wire arc additive manufacturing (WAAM) is a variant of additive manufacturing which allows economical production of large-scale and high-density parts. The WAAM process has been studied extensively on different steels; however, the influence of process parameters, specifically wire feed speed (WFS), travel speed (TS), and their ratio on bead geometry, microstructure, and mechanical properties, are yet to be studied. The present work aims at closing this gap by using the WAAM process with robotic cold metal transfer (CMT) technology to manufacture high-strength structural steel parts. For that purpose, single-bead welds were produced from HSLA steel by varying WFS between 5 and 10 m/min and the WFS to TS ratio between 10 and 20. Those variations produce heat inputs in the range of 266–619 J/mm. The results have shown that the wire feed speed to travel speed ratio is the major parameter to control the heat input. Increasing heat input increases characteristic bead dimension, whereas it reduces the hardness. In the second part of experiments, two single-bead walls were deposited via the parallel deposition strategy and one multiple-bead wall was produced using the oscillation strategy. The tensile properties were tested along two directions: parallel and perpendicular to deposition directions. For the yield strength and tensile strength, the difference between horizontally and vertically tested specimens was smaller than the standard deviations. On the other hand, the total and uniform elongation values exhibit up to 10% difference in the test direction, indicating anisotropy in ductility. Those tensile properties were attributed to repeated thermal cycles during the WAMM process, which can cause heat transfer in multiple directions. The yield strength of the multiple-bead wall produced via oscillation was lower, whereas its ductility was higher. The tensile properties and hardness differences were found to correlate well with the microstructure.

Wire arc additive manufacturing of thin and thick walls made of duplex stainless steel

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Microstructural Evolution, Mechanical and Electrochemical Performance of Duplex Stainless Steel Fabricated by Wire Arc Additive Manufacturing with ER2209 Filler Wire

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Wire arc additive manufacturing of high-strength low alloy steels: study of process parameters and their influence on the bead geometry and mechanical characteristics

Wire arc additive manufacturing using high-strength steel tubular and solid wires

Microstructural Evolution in a Thin Wall of 2cr13 Martensitic Stainless Steel During Wire Arc Additive Manufacturing

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

The state-of-the-art of wire arc directed energy deposition (WA-DED) as an additive manufacturing process for large metallic component manufacture

Effect of Mn Content on the Microstructure and Corrosion Resistance of Duplex Stainless Steels Fabricated by Wire Arc Additive Manufacturing

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Study of the Impact of the Synergic Line and the Strategy of Conception on Ti-6Al-4V Wire Arc Additive Manufacturing Process (WAAM-CMT)

Effect of nitrogen content on microstructure and mechanical properties of duplex stainless steels via wire arc additive manufacturing

Mechanical properties of wire and arc additively manufactured high-strength steel structures

Microstructure, Mechanical and Electrochemical Properties of Wire-Arc Additively Manufactured Duplex Stainless Steel

Microstructure and Mechanical Properties of Layered Billets from Various Grades of Austenitic Steels Grown by Additive Electric Arc Welding

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Microstructural development during wire arc additive manufacturing of copper-based components

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels