Abstract:The tensile behavior of Ti6Al4V–5Cu alloy studied in the temperature range of 450–550 °C at the strain rate interval of 10 −3 -10 −1 s −1 . Alloy deformation behavior, microstructure evolution, and its relative internal structure changes due to deformation were investigated. The tensile behavior of the alloy had elucidated in terms of change in true stress-strain relationship. At 450 °C, the alloy showed the decrease of peak stress at the strain rate interval of 10 −3 -10 −2 s −1 , which suggests Ti6Al4V–5Cu plastic flow behavior, was quite different. The alloy exhibited an elongation (El) of 28% at 450 °C in a strain rate of 10 −3 s −1 . At 10 −3 s −1 , the El of the alloy decreased with the increase of forming temperature. However, at 10 −2 s −1 and 10 −1 s −1 , the El increased with the rising of temperature. Scanning electron microscope (SEM) was used to investigate the microstructure of Ti6Al4V–5Cu alloy. The alloy grain boundaries (GBs) were found as continuous and discontinuous structural features, especially the high angle grain boundaries (HAGBs). The GB feature has contributed to the initiation of micro-cracks because of the creation of weakest regions in the material during deformation. The nature of GB geometry has also a tremendous contribution to the workability of Ti6Al4V–5Cu alloy at low forming temperatures. The presence of a high amount (%) LAGBs and the serrated nature of HAGBs structures determined the pull to grain pieces. The deformation mechanism of the Ti6Al4V–5Cu alloy at low forming temperatures was accomplished initially by boundary serration phenomenon due to strain-induced GB migration related to heat treatment at low strain condition, then by initiation of recrystallized grains-triggered by the plasticity behavior of strain induced sub-boundaries, and finally by the development of deformed grains generated by the reduction in corrugation propensity of GBs due to high strain condition.

Special Features of Structure Formation and Properties of Special High-Alloy Alloys of the Al – Si – Cu System

Features of structure formation and thermal expansion of high alloys of the Al–Si–Cu system

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Composition- and Temperature-Dependent Liquid Structures in Al–Cu Alloys: Anab Initiomolecular Dynamics and X-Ray Diffraction Study

Effects of Copper Content and Thermo-Mechanical Treatment on Microstructure and Mechanical Properties of AlMgSi(Cu) Alloys

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Unsteady-State Horizontal Solidification of an Al–Si–Cu–Fe Alloy: Relationship Between Thermal Parameters and Microstructure with Mechanical Properties/Fracture Feature

Microstructure, Phase Formation and Heat-Treating of Novel Cast Al-Mg-Zn-Cu-Si Lightweight Complex Concentrated Aluminum Based Alloy

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

A study of the Cu0.95Al0.05 alloy: stress-strain curve and microstructure

Investigation on Compressive Behavior of Cu-35Ni-15Al Alloy at High Temperatures

Solidification Paths and Phase Components at High Temperatures of High-Zn Al-Zn-Mg-Cu Alloys with Different Mg and Cu Contents

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Microstructures and mechanical properties of Cu-Sn alloy subjected to elevated-temperature heat deformation

Physical and Mechanical Properties of Cu-Fe System Functionally Graded and Multimaterial Structures after the DED

Effect of CuO Nanostructure Addition and Cooling Rate on the Microstructure and Mechanical Characteristics of Hypoeutectic Al-2wt.%Si Alloy

Effect of Casting Process and Thermal Exposure on Microstructure and Mechanical Properties of Al-Si-Cu-Ni Alloy

Evaluation of critical temperatures of as-cast Co-based superalloys as a function of alloying elements and their effect on microstructure

Linear Thermal Expansion and Specific Heat Capacity of Cu-Fe System Laser-Deposited Materials

Phase Composition and Structure of Al–Cu–Mn–Mg–Zn–Fe–Si Alloys Containing 2% Cu and 1.5% Mn

FORMING AN EDGED CUBIC TEXTURE IN BAND SUBSTRATES MADE OF (Cu+Ni)–Me (Me=Mo, Mn, Nb) ALLOYS FOR HIGH-TEMPERATURE SECOND-GENERATION SUPERCONDUCTORS