Abstract:The Ag-Cu alloys have received attention due to their excellent electrical and mechanical properties. However, the analytical research on why the mechanical properties of the Ag-Cu alloys increase after a small amount of Cu atoms are added is still lacked. In this work, the classical molecular dynamics (MD) simulations method was used to establish the Ag-Cu alloy models with different Cu contents. The tensile deformation mechanism of Ag-Cu alloy at room temperature was revealed from the atomic scale through the analysis of the stress-strain behavior and the evolution of dislocations. During the simulations, the embedded atom method (EAM) potential was used to describe the interaction between Ag atom and Cu atom. The uniaxial tensile deformation and nanostructure evolution of Ag-3 at.% Cu, Ag-6 at.% Cu and Ag-10 at.% Cu alloy models at the temperature of 300 K and the strain rate of 0.02 Å/ps were studied in detail. Results show that the internal stress was generated due to the large lattice mismatch among Ag atom, Cu cluster and the grain boundary. It results in the formation of dislocation and the negative initial stress at the beginning stage of Ag-Cu alloy models under tension. The dislocation firstly nucleates at the grain boundary and the growth rate of dislocation is slow before the crack propagation, and the complex dislocation reactions also exist. With the increase of Cu content, the tensile strengths of Ag-Cu alloys also increase. Cracks mainly form at the intersection of multiple grains, and the fracture mode changes from the intergranular fracture to the intergranular fracture and transgranular fracture after the unstable propagation of cracks. Meanwhile, a plenty of Cu atoms are distributed in the form of clusters in Ag matrix. They hinder the slip of dislocation and slow the relative sliding between atomic layers, and thus finally improves the deformation resistance to the plastic deformation of Ag-Cu alloy. The study on the tensile deformation behavior of Ag-Cu alloy at room temperature has certain guiding significance for the practical production and application of the design of Ag-Cu alloy.

A study of the Cu0.95Al0.05 alloy: stress-strain curve and microstructure

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

The Microstructure and tensile properties of a splat-quenched Al-Cu-Li-Mg-Zr alloy

Etude par diffraction des rayons X et microscopie électronique en transmission d'un alliage Cu–1,35 at.% Sn déformé par compression

An analysis of the influence of the precipitate type on the mechanical behavior of Al-Cu alloys by means of micropillar compression tests

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Investigation on Compressive Behavior of Cu-35Ni-15Al Alloy at High Temperatures

Study of strengthening mechanisms in Al-Cu and Al-Cu-Mg systems subjected to plastic deformation and T6 treatment

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Investigation of deformation behavior and strain-induced precipitations in Al-Zn-Mg-Cu alloys across a wide temperature range

Effect of Alloying on Dislocation Structure, Cracking and Fracture of Cu–Al and Cu–Mn Alloys in Low-Stability States

EXPERIMENTAL INVESTIGATION ON THE STRESS-INDUCED MARTENSITIC TRANSFORMATION AND THE MICROSTRUCTURE EVOLUTION IN CuAlNi SINGLE CRYSTAL

Microstructure, tensile properties and fracture behaviour of an Al-Cu-Li-Mg-Zr alloy 8090

Effect of CuO Nanostructure Addition and Cooling Rate on the Microstructure and Mechanical Characteristics of Hypoeutectic Al-2wt.%Si Alloy

The tensile behaviors of Ag-Cu alloys with different Cu contents: Molecular dynamics simulations study

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Effect of Cu–Al Ratio on Microstructure and Mechanical Properties of Cu–Al Alloys Prepared by Powder Metallurgy

Microstructures and mechanical properties of Cu-Sn alloy subjected to elevated-temperature heat deformation