Abstract:Large storage tanks for oil storage are widely used in petrochemical industry. Corrosion in the tank floor and wall is a serious threat for environmental and economic safety. Owing to their unique potential for long-range, in-plane propagation through plates, Ultrasonic Guided Waves (UGW) offer an obvious solution in the development of an on-board structural health-monitoring (SHM) system, providing assessment of structural integrity for storage tank floor and wall defect in-situ inspection. This paper presents this application by focusing on their propagation through the plate structure. Even very small mechanical discontinuity or geometry change of plate structure, e.g. corrosion defect on tank floor, will influence the propagation characteristic of the guided waves. These effects are measured as mode changes, frequency shifts or filtering, reflection and diffraction of new ultrasonic modes or overall distortion of the original ultrasonic signals. By capturing and analyzing these changes we can deduct the corrosion defect of the tank floor and wall which causes the ultrasonic signal change and interactions. The T/R transducers are required to be attached on the outer edge of the tank floor and outer surface of the tank wall. The technique is developed based on the Lamb wave transmission tomography. Starting from the dispersion curve and choosing the appropriate wave mode, the propagation of the guided waves in the tank floor and wall has been carried out through numerical simulation and the experiment has been conducted for verification using the full-size oil storage tank. The low frequency guided waves can propagate longer distance in planar and tubular structures. The later has been already used in pipeline inspection. The complexity of the application of ultrasonic guided wave in tank floor inspection lies in the object containing multiple lap joint welds along the large diameter of the tank (up to 100 m) and the complicated reconstruction of the two-dimensional defect distribution information.The main scope of the investigation was the application of the ultrasonic transmission tomography for localization of non-uniformities of inside tank floor, taking into account ultrasonic signal losses due to the loading with oil on the top and ground support at the bottom for the tank floor, and the loading with oil inside for the vertical tank wall.

Ultrasonic Torsion Mode Guided Wave Probe Design for Local Detection of Vehicle-mounted Winding Hydrogen Storage Cylinders

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Implementing Ultrasonic Guided Wave Mode Control in Hollow Cylinders

Ultrasonic Guided Wave Approach Incorporating SAFE for Detecting Wire Breakage in Bridge Cable

DEVELOPMENT OF STRIP WINDING HIGH PRESSURE HYDROGEN STORAGE VESSEL WITH LOW STRESS INNER LINER

Non-Destructive Testing Study of Hydrogen Storage COPVs Based on Digital Shearography Technique

Damage Localization in Hydrogen Storage Vessel by Guided Waves Based on a Real-Time Monitoring System

Radial Displacement Measurement of Hydrogen Storage Cylinders under Internal Pressure Based on Fringe Projection Profilometry

Damage Detection And Leakage Alert Of Fiber Composite Wrapped Tank For High Pressure Hydrogen Storage

Detection of Void and Crack Defects in Type IV Hydrogen Storage Vessels by Microwave Technique

Excitation of Axisymmetric and Non-Axisymmetric Guided Waves in Elastic Hollow Cylinders by Magnetostrictive Transducers

Design and experimental study of electromagnetic ultrasonic single-mode guided wave transducer for small-diameter stainless steel tubes

Storage Tank Floor and Wall Defect In-Situ Inspection with Ultrasonic Guided Wave Technique

The Detection of Hydrogen with A Nanotube Structured Sensor

Analysis of Hydrogen Embrittlement on Aluminum Alloys for Vehicle-Mounted Hydrogen Storage Tanks: A Review

Study on inserted curved surface coupling phased array ultrasonic inspection of multi-layered steel vessel for high-pressure hydrogen storage

Enhanced Nondestructive Testing Using Pulsed Eddy Current and Electromagnetic Ultrasonic Techniques

Identifying Void and Crack Defects in Type III Hydrogen Storage Vessels Based on Microwave Inspection

Ultrasonic testing and Monitoring of Hydrogen blistering and Hydrogen-induced Cracking of LPG Storage Tanks

Strain Analysis and Non-Destructive Monitoring of the Two-Stage Hydraulic-Driven Piston Compressor for Hydrogen Storage

Hydrogen Embrittlement Detection Technology Using Nondestructive Testing for Realizing a Hydrogen Society