Abstract:Due to mass diffusion issues, it is challenging to prepare black-phase thick formamidinium-based perovskite (FAPbI3) films via vapor approaches. Precursor engineering is employed here to overcome the dilemma of thorough reaction and black-phase stabilization of FAPbI3 in a sequential vapor approach. For the first time, FAPbBr3 was used as an additive in the precursor to promote the formation of FAPbI3 perovskite. To balance off the increased crystallization degree of precursor films due to the addition of FAPbBr3, CsI dissolved in dimethyl sulfoxide (DMSO) was further added. It is indicated that the simultaneous incorporation of FAPbBr3 and CsI-DMSO successfully accelerated the formation rate of perovskite and inhibited the formation of FAPbI3 yellow phase. The power conversion efficiency of the as-prepared devices of different areas (0.1125 or 1 cm2) reached 20%, the first report of large-area 20%-efficiency PSCs based on a vapor approach, highlighting its applicability to large-area manufacture in the future. Furthermore, when blade coating is used in preparing the precursor film, the efficiency reached 19%. When the precursor film was prepared by dip coating, we could prepare conformal FAPbI3 coatings on carbon fibers, suggesting possible future applications in fabricating wearable PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c10379?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c10379</a>.Figures S1–S3, optimization of procedures; Figures S4 and S5, AFM and transient PL mapping images; Figures S6 and S12, XRD and UV–vis absorption spectra; Figures S7 and S8, photos of precursor films and CsX-DMSO solutions; Figure S9, XPS results; Figure S10, UV–vis absorption spectra; Figure S11, device performance statistics; Figures S13 and S14, derivation of bandgap and Urbach energy; Figure S15, stability; Figures S16 and S17, comparison of precursor films fabricated by blade- or spin-coating; Figure S18, SEM and XRD of perovskite on carbon cloth; and Table S1, summary of PSCs fabricated by VASP in literature (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c10379/suppl_file/am0c10379_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Thermal assisted blade coating methylammonium lead iodide films with non-toxic solvent precursors for efficient perovskite solar cells and sub-module

Preparing High-Efficiency Perovskite Solar Cells

The Effects of Solvent on Doctor‐Bladed Perovskite Light Absorber under Ambient Process Condition for Multiple‐Cation Mixed Halide Perovskites

Ambient blade coating of mixed cation, mixed halide perovskites without dripping: <i>in situ</i> investigation and highly efficient solar cells

Preparation of CH3NH3PbI3 Thin Films for Solar Cells Via Vapor Transfer Method

Morphology Control towards Green Solvent System Processed High Performance Semitransparent CH3NH3PbI3 Film for Perovskite Solar Cell

Thermally Induced Crystallization of High Quality CH3 NH3 PbI3 Film with Large Grains for Highly Efficient Perovskite Solar Cells.

Controllable Crystallization of Perovskite Films during the Blade-Coating Fabrication Process for Efficient and Stable Solar Cells

High-quality CsPbBr3 films prepared by introducing methylammonium iodide into PbBr2 precursor for efficient perovskite solar cells

Lead halide–templated crystallization of methylamine-free perovskite for efficient photovoltaic modules

Controllable Cosolvent Blade-Coating Strategy Toward Low-Temperature Fabrication of Perovskite Solar Cells

Controllable Blading Interdiffusion of Formamidinium Iodide on Thermal Evaporated Scalable and Conformal Lead Iodide for Efficient Perovskite Solar Cells

Vacuum-Assisted Thermal Annealing of CH3NH3PbI3 for Highly Stable and Efficient Perovskite Solar Cells

Morphology Optimization of Perovskite Films for Efficient Cells and Modules through Solvent Engineering

te thin fi lms and e ffi cient perovskite solar cells prepared by the hybrid deposition method †

Precursor Engineering of Vapor-Exchange Processes for 20%-Efficient 1 cm 2 Inverted-Structure Perovskite Solar Cells

2,2‐Azodi(2‐Methylbutyronitrile)‐coordinated Intermediate Phase Engineering for Efficient and Stable Perovskite Solar Cells

Preperation of Perovskite Materials and Perovskite Solar Cells by Vapor-Assisted Solution Process

Tunable Crystallization and Nucleation of Planar CH3NH3PbI3 Through Solvent-Modified Interdiffusion

Advancements in Perovskite Solar Cell Efficiency Through Blade Coating Techniques and Post-Treatment Optimization

High-Quality Perovskite CH3NH3PbI3 Thin Films for Solar Cells Prepared by Single-Source Thermal Evaporation Combined with Solvent Treatment