Abstract:Powered by the worldwide efforts of research groups experienced in dye‐sensitized, and thin‐film solar cells, perovskite solar cells (PSCs) reached a power conversion efficiency of 25.7% within 10 years. However, the presence of defects and trap density within the active layer's grain boundaries commonly operates as non‐radiative recombination centers. Hence, intensive efforts have been reported to passivate the inevitable bulk and interface defects of the active layer using additives or post‐treatment processing to enhance the efficiency and stability of PSCs. Herein, a facile post‐treatment strategy based on wet processing methylammonium lead triiodide, MAPbI3 (prepared from lead acetate and methylammonium iodide precursors) films with organic amine salts (FABr and FAI) is demonstrated. As a result, high‐quality films of mixed perovskites (FAxMA1‐xPbI3‐xBrx and FAxMA1‐xPbI3) were obtained. The surface treatment has efficiently passivate the defects in the host film, suppressing the non‐radiative carrier recombination. Compared to the control device, the increased open‐circuit voltage (from 0.5 V to 1 V) and fill factor (FF) values of the optimized device based on FAxMA1‐xPbI3 showed a PCE of 16.13%. And our findings revealed that post‐treatment is possible on wet perovskite film aged for a few minutes prior to its post‐treatment, which saved the energy used for pre‐annealing. Post‐treatment has been carried out on wet host film of (MAPbI3) aged for 3 minutes prior to its treatment. The host film, with evident pinholes was changed into smooth morphology and larger grain‐size mixed FAxM1‐xPbI3‐xBrx and FAxMA1‐xPbI3 films upon post‐treatment using FABr and FAI solutions respectively. Compared to the control device, the post‐treated devices had higher fill factor (FF) and a double rise in Open‐circuit voltage (VOC), leading to enhanced device efficiency. Our findings has also proved that post‐treatment is possible on wet films that saved the energy for pre‐annealing during post‐treatment.

Advancements in Perovskite Solar Cell Efficiency Through Blade Coating Techniques and Post-Treatment Optimization

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Crystallization Control of Blade‐Coated Wide Bandgap FACs‐Based Perovskite

Efficient Perovskite Solar Cells Fabricated Through CsCl-Enhanced PbI2 Precursor Via Sequential Deposition.

Blade-Coating of High Crystallinity Cesium-Formamidinium Perovskite Formulations

Acetic Acid Assisted Crystallization Strategy for High Efficiency and Long-Term Stable Perovskite Solar Cell

Single‐step post‐production treatment of lead acetate precursor‐based perovskite using alkylamine salts for reduced grain‐boundary related film defects

Methylammonium Chloride Additive in Lead Iodide Optimizing the Crystallization Process for Efficient Perovskite Solar Cells

Bridging‐Solvent Strategy for Quasi‐Single‐Crystal Perovskite Films and Stable Solar Cells

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells

Lead Iodide Redistribution Enables In Situ Passivation for Blading Inverted Perovskite Solar Cells with 24.5% Efficiency

Amino acid salt Induced PbI2 crystal orientation Optimization for High-Efficiency Perovskite Solar Cells with Long-Term Stability

Retarding Ion Migration for Stable Blade‐Coated Inverted Perovskite Solar Cells

Regulating the Crystallization of FAPbI3‐Based Perovskite with a Furan Substituted Ethylammonium Additive for Achieving Highly Efficient Solar Cells

Enhancing the Efficiency and Stability of Triple-Cation Perovskite Solar Cells by Eliminating Excess PbI2 from the Perovskite/Hole Transport Layer Interface

Optimizing Blade‐Coated Tin–lead Perovskite Solar Cells and Tandems with Multi‐Carboxyl and Amino Group Integration

Controllable Crystallization of Perovskite Films during the Blade-Coating Fabrication Process for Efficient and Stable Solar Cells

Intermediate Phase Modification Enables High‐Performance Iodine‐Rich Inorganic Perovskite Solar Cells with 3000‐Hour Stability