Abstract:Fully-transparent deep-sea pressure hulls have been attracted attention in recent years with the increasing demand for underwater observation. So far, public researches on design rule and failure modes for fully-transparent deep-sea pressure hulls are limited and the relevant experience cannot meet the requirements of new cabin design. In this study, the compression test is carried on, in which the material samples are subjected to quasi-static compressive load until failure in tests at different loading rates, and the hyperelastic finite element model is established in LS-DYNA software to simulate the failure process. Simulation results of material properties in finite element analysis on the cylindrical samples are compared with the experimental data, including the characteristic points of the mechanical properties in elastic stage and hardening stage, the ultimate load and failure mode of the samples. Mesh convergence analysis is conducted, and the appropriate mesh quality is accordingly selected in simulation of fully-transparent deep-sea pressure hulls. An equation for prediction of instability-type failure is described, which is derivation based on the classical analytical expression of elastic instability, thus, when 5 times of safety factor is taken, the wall thickness of the pressure hull is calculated to be t/R 0 = 0.0685 at 2,500 m depth. Ultimate strength and failure mode of a typical fully-transparent deep-sea pressure hull are simulated. First, the first-order linear buckling modal analysis is carried out to simulate initial geometric imperfections. Then, simulations for the loading and collapse process of two fully-transparent pressure hulls respectively with one opening and two openings are conducted, and the ultimate load of 126 MPa and 128 MPa for the two kinds of hulls are obtained. Finally, simulation of a scaled pressure hull is carried out and simulation results are compared with the experimental data in reference, which are basically consistent. The calculated failure strength shows that the spherical hulls satisfy the safety factor requirement of 5 times. The provided simulation procedure can be referred for failure analysis of fully-transparent pressure hulls.

Establishment and Program development of failure criterion of hollow glass microspheres/epoxy resin composites based on tension/compression discrepancy

Micromechanics-based Progressive Failure Analysis of Carbon FIber/epoxy Composite Vessel under Combined Internal Pressure and Thermomechanical Loading

Development and Mechanical Characterization of HGMS–EHS-Reinforced Hollow Glass Bead Composites

Experimental investigation of the hydrostatic compression of a hollow glass microspheres/epoxy resin under high‐pressure conditions at the full ocean depth

Studies on Compressive Behaviors of Hollow Glass MicrospheresFilled Epoxy Resin Composites

Micromechanics-based Burst Failure Analysis of Composite Vessel Used for Hydrogen Storage

Prediction of long-term fatigue life of CFRP composite hydrogen storage vessel based on micromechanics of failure

Isogeometric Method for Buckling Prediction and Post-Buckling Analysis of Variable Stiffness Composite Underwater Pressure Shell

Finite Element Analysis of Adhesive Failure of Solid Composite Propellant Multi-material Structure for Underwater Intelligent Equipment

Experimental Investigation and Design of Hollow Section, Centrifugal Concrete-Filled GFRP Tube Columns

Prediction of the inter-fiber mechanical properties of composites: Part II Failure criterion based on micromechanics and cross-scale stress calculation

Experimental investigation of failure modes and ultimate strength of GFRP structure members under longitudinal compression

Analysis, Simulation and Experimental Study of the Tensile Stress Calibration of Ceramic Cylindrical Pressure Housings

Research on Preparation and Properties of Solid Buoyancy Materials Filled with Hollow Glass Microspheres

Research Frontier on Solid Buoyancy Materials

Failure Analysis of Syntactic Foams: A Computational Model with Cohesive Law and XFEM

Experimental study and numerical prediction of tensile strength properties and failure modes of hollow spheres filled syntactic foams

Experimental and Numerical Investigation of Material Failure Criterion with High-Strength Hull Steel under Biaxial Stress

The failure behavior of syntactic foams as buoyancy materials for deepsea applications

A 3D Micromechanics-Based Failure Criterion for Fiber Reinforced Composites under Longitudinal Compression

Failure analysis on fully-transparent deep-sea pressure hulls used at 2,500 m depth