Abstract:Deep‐sea equipment is generally made of lightweight and pressure‐resistant materials in order to meet the requirements of the actual work. In order to explore marine resources better, it is necessary to research lightweight buoyancy materials for loading on mining equipment. These buoyancy materials contribute not only to providing adequate buoyancy to the mining equipment but also to reducing economic expenses. In this paper, hollow glass microspheres reinforced epoxy hollow spheres (HGMSs‐EHSs) were prepared by the rolling ball method using expanded polystyrene (EPS), epoxy resin (EP), and HGMS as raw materials. Epoxy syntactic foam (ESF) was manufactured by blending EP, curing agent, HGMS, and HGMS‐EHS with molding method. Basalt fiber (BF) reinforced ESF was fabricated by adding BFs to form a fiber network inside the syntactic foam. The results revealed that the density and compressive strength of ESF increased progressively with the number of HGMS‐EHS layers. The density and compressive strength of ESF decreased prospectively with the increase of the stacking volume fraction of HGMS‐EHS. The density and compressive strength of ESF increased gradually with the enlargement of the length and content of BF. In the range of influencing factors mentioned above, the density of ESF remains around 0.3 g/cm3, which has a low density. When the number of layers of HGMS‐EHS was two, the stacking volume fraction was 90%, the length of BF was 12 mm, the content of BF was 4%, the density of BF‐ESF was 0.316 g/cm3, and the compressive strength was 6.93 MPa. The compressive strength of prepared buoyancy material can meet the pressure resistance requirements for operations in waters of a certain depth. With a density of only 0.316 g/cm3, it provides sufficient buoyancy to balance the gravity of the equipment. Compared with the current study, in this paper, BFs were used as the reinforcing phase to prepare solid buoyancy foam with low density and high compressive strength. The experimental results demonstrate that this economical fiber material can effectively improve the compressive strength of buoyancy materials. This buoyancy material may be suitable for loading on small equipment for extracting marine resources. This work provides a reference for the preparation of low‐density solid buoyancy materials.

The failure behavior of syntactic foams as buoyancy materials for deepsea applications

Failure Analysis of Syntactic Foams: A Computational Model with Cohesive Law and XFEM

Strength Analysis of Syntactic Foams Using a Three-Dimensional Continuum Damage Finite Element Model

Recent developments on epoxy-based syntactic foams for deep sea exploration

Effect of curing agents and hollow glass microspheres on the compression properties of syntactic foams

Influence of a batch of hollow glass microspheres with different strength grades on the compression strength of syntactic foam

Anisotropic compression response of functionally gradient syntactic foam comprising of fly ash cenosphere and polyurethane

Finite Element Analysis of Adhesive Failure of Solid Composite Propellant Multi-material Structure for Underwater Intelligent Equipment

Compressive Behavior and Failure Mechanisms of Freestanding and Composite 3D Graphitic Foams

Modelling the dynamic compressive response of syntactic foam with hierarchical cell structure

Experimental investigation of the hydrostatic compression of a hollow glass microspheres/epoxy resin under high‐pressure conditions at the full ocean depth

Underwater impulsive resistance of the foam reinforced composite lattice sandwich structure

Fabrication and Compression Properties of Reinforced Epoxy Syntactic Foam With Basalt Fiber

Fundamental mechanical relations of open-cell metal foam composite materials with reticular porous structure

Mechanical Properties Test and Failure Analysis of Composite Foam Sandwich Structure in Ramp-Down Zone

Compression properties of polymeric syntactic foam composites under cyclic loading

Compressive properties of co-continuous hollow glass microsphere/epoxy resin syntactic foams prepared using resin transfer molding

Introducing Auxetic Behavior to Syntactic Foams

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Failure analysis on fully-transparent deep-sea pressure hulls used at 2,500 m depth

Preparation, compression behavior and 3D damage evolution of epoxy syntactic foam with nickel hollow spheres