Abstract:This work aims at investigating the causes affecting the dimensional and geometrical accuracy of holes in metal binder jetting stainless steel parts. Parallelepiped samples with a through hole were produced using AISI 316L and 17-4PH powders, differing for diameter (3, 4, 5 mm), and position of the axes with respect to the building plane (6, 9, 12 mm distance). Dimensions and geometrical characteristics were measured at green and sintered state by a coordinate measuring machine, determining the dimensional change and the geometrical characteristics. As expected, the shrinkage of linear dimensions is anisotropic; moreover, change in volume and sintered density are significantly affected by the position in the printing chamber. Higher shrinkage was measured along building direction (Z) – 18.5 ÷ 19.5%, than in the building plane – 16.5 ÷ 17.5%, and slightly higher shrinkage – 0.5 ÷ 0.8% was measured along powder spreading direction (X) than binder injection direction (Y). A variation up to 3% in relative density of sintered parts depending on the position in the building plane was observed in 316L. The dimensional change of diameters generally confirmed the shrinkage predicted by the model previously developed—difference between real and expected dimensional changes lower than 3%, except for three geometries (4 ÷ 6%). The cylindricity form error of sintered parts was strongly underestimated by the prediction model (up to 0.15 mm), but underestimation was considerably reduced (generally lower than 0.05 mm) adding the cylindricity form error due to printing. Dimensional and geometrical accuracy of holes are strongly affected by shape distortion of the parallelepiped geometry, in turn due to layer shifting and inhomogeneous green density during printing, and to the effect of frictional forces with trays during sintering. Gravity load effect was also observed on the holes closest to the building plane. Future work will improve the reliability of the prediction model implementing the results of the present work.

Study of microstructure and mechanical properties of 17-4 PH stainless steel produced via Binder Jetting

Effect of Printing Orientation Angle and Heat Treatment on the Mechanical Properties and Microstructure of Binder-Jetting-Printed Parts in 17-4 PH Stainless Steel

Influence of powder particle size distribution on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by selective laser melting

Microstructural and Mechanical Characterization of Selective Laser Melted 17-4 PH Stainless Steel: Effect of Laser Scan Strategy and Heat Treatment

Tailoring microstructure and mechanical properties of 17-4PH steel fabricated by wire-arc directed energy deposition via a combination of intrinsic and post-processing heat treatments

Effect of heat treatment on microstructure and mechanical properties of 17-4PH stainless steel manufactured by laser-powder bed fusion

Influence of Sintering Atmosphere, Temperature and the Solution-Annealing Treatment on the Properties of Precipitation-Hardening Sintered 17-4 PH Stainless Steel

Microstructure and Defect Analysis of 17-4PH Stainless Steel Fabricated by the Bound Metal Deposition Additive Manufacturing Technology

A review on the production of 17-4PH parts using press and sinter technology

Effect of Process Parameters on Density and Mechanical Behaviour of a Selective Laser Melted 17-4PH Stainless Steel Alloy

Effect of hot isostatic pressing on the microstructure and mechanical properties of 17-4PH stainless steel parts fabricated by selective laser melting

Effect of powder chemical composition on the as-built microstructure of 17-4 PH stainless steel processed by selective laser melting

Effect of heat treatment on microstructure and tensile property of 420 martensitic stainless steel produced by binder jetting additive manufacturing

Mechnical properties of 17-4PH stainless-steel at various laser sintering process parameters

Effect of hot isostatic pressing treatment on porosity reduction and mechanical properties enhancement of 316L stainless steel fabricated by binder jetting

Effect of homogenization on precipitation behavior and strengthening of 17-4PH stainless steel fabricated using laser powder bed fusion

Effect of sintering temperature on binder jetting additively manufactured stainless steel 316L: densification, microstructure evolution and mechanical properties

Microstructural, Mechanical, and Electrochemical Corrosion Properties of Extrusion Additive Manufactured 17-4 Precipitation Hardenable Stainless Steel

Analysis of the causes determining dimensional and geometrical errors in 316L and 17-4PH stainless steel parts fabricated by metal binder jetting

17-4 PH Steel Parts Obtained through MEX and PBF-LB/M Technologies: Comparison of the Structural Properties

Influence of initial relative densities on the sintering behavior and mechanical behavior of 316 L stainless steel fabricated by binder jet 3D printing