Abstract:The cement industry is one of the primary sources producing anthropogenic CO2 emissions. The significant increase in the demand for cement in years has significantly contributed to the increase in carbon emissions. Among numerous CO2 treatment technologies, calcium looping (CaL) is a practical approach to mitigating CO2 emissions. This paper used calcium looping (CaL) to capture CO2 from flue gas in a cement pre-calciner kiln system. The raw material exiting the lowest stage of the preheater is used as a calcium-based adsorbent, and the carbonation reactor is built between the tertiary and secondary preheaters, using the high-temperature flue gas exiting the tertiary preheater to provide heat for the reaction. The CFD (Computational Fluid Dynamics) simulation technology was used to evaluate the rationality of the carbonation reactor and the key factors affecting the carbon removal efficiency of the carbonation reactor. The results indicate that the velocity and pressure fields of the carbonation reactor conform to the general operating rules and are reasonable. The optimal operating speed of particles in the carbonation reactor is 15 m/s, with a separation efficiency of particles of 92.5%, ensuring the smooth discharge of reaction products. The factor analysis of the carbonation reactor shows that when the temperature is 911 K, the mass flow rate of CaO is 2.07 kg/s, and the volume fraction of CO2 is 0.28, the carbonation reaction reaches a chemical equilibrium state, and the carbon removal efficiency is 90%. It should be noted that this carbon removal efficiency is the optimal carbon removal efficiency based on a combination of economic factors. In addition, the influencing factors show a precise sequence: CO2 volume fraction > CaO addition amount > temperature. Finally, we investigated the impact of the addition of the carbonation reactor on the preheater system. The results show that adding the carbonation reactor causes an increase in the flue gas velocity at the outlet of the preheater and a decrease in pressure, reducing the separation efficiency. Although the separation efficiency decreases slightly, the impact on the pre-calciner system is minimal.

Optimization of Fuel In-Situ Reduction (FISR) Denitrification Technology for Cement Kiln using CFD Method

Experimental Study of Effects of Pulverized Coal Characteristics on the Conversion of Fuel Nitrogen to NOx

An efficient and economic denitration technology based on fuel pretreatment for cement cleaner production

Numerical simulation of low nitrogen oxides emissions through cement precalciner structure and parameter optimization

Denitration Simulation of SNCR System Nozzles at Different Layout Positions in Coal Powder Boilers

Evaluation of adaptive neuro-fuzzy inference system-genetic algorithm in the prediction and optimization of NOx emission in cement precalcining kiln

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

A Pilot-Scale Test Facility of 500 Kwth for Industrial Cfb Boilers on Low Nitrogen Combustion-Discussion of Design, Experiment, and Economic Analysis

Enhancing Simultaneous Desulfurization and Denitrification Efficiency of Cement Kiln Exhaust Gas Via Co-Catalytic Fenton Oxidation Process

Experimental study and CFD modeling of NOx reduction and reductive gas formation in deep reburning of cement precalciner

A multistage NOx reduction process for a FCC regenerator

Numerical simulation of flue gas recirculation in a lime rotary kiln

Effects of Co-Firing Biomass and Pulverized Coal on NO Reduction in Cement Precalciner

Numerical Simulation of CO2 Extraction from the Cement Pre-Calciner Kiln System

CFD-aided Optimization of the Decomposition Kinetics of Cement Raw Meals under High CO2 Concentrations

Experimental evaluation of rich oxyfuel combustion characteristics in varying over-stoichiometric conditions

CFD-aided optimization of the decomposition kinetics of cement raw meals under high CO 2 concentrations

Investigating the Optimization Design of Internal Flow Fields Using a Selective Catalytic Reduction Device and Computational Fluid Dynamics

Experimental Investigation on the Conversion of Fuel-N to NOx of Quasi-Particle in Flue Gas Recirculation Sintering Process

Simulation and Optimization of SNCR Process

Process compatible desulfurization of NSP cement production: A novel strategy for efficient capture of trace SO 2 and the industrial trial