Abstract:For recent lithium-ion batteries (LIBs), there have been lots of researches about convert liquid-phase electrolyte to solid-state electrolyte (i. e. all-solid-state battery) to improve safety and stability. Solid-state electrolyte materials have to satisfy some criteria including high ionic conductivity at room-temperature, chemical stability against reducing environment, and mechanical strength. Many solid-materials for electrolyte have been researched, including perovskite, garnet, and sulfide-type of materials. Among them, garnet-type based lithium lanthanum zirconium oxide (LLZO, Li 7 La 3 Zr 2 O 12 ) has been received attention due to its high ionic conductivity (~10 -4 S/cm at room temperature) and wide electrochemical stability window (~6 V versus Li/Li + ). The main issue of LLZO is the high interfacial resistance with anode and cathode materials such as Li metal and LiCoO 2 . Many researchers have tried to understand the cause of this interfacial resistance for LLZO. K. Park et al. researched about the cathode/electrolyte (LLZO) interface and revealed co-diffusion and second-phase formation of LLZO at high-temperature [1]. M. Zarabian et al. reported that spin-coated LLZO on the LiCoO 2 pellet fabricated at low-temperature (~400 o C) and co-diffusion of La and Co at the interface by using X-ray photoelectron spectroscopy (XPS) [2]. They commonly suggested that elevated temperature make chemical interaction and this make high interfacial resistance. In this study, we adopted novel sintering method, flash light annealing (FLA) process, to fabricate LLZO solid-electrolyte. This method is also called rapid, cool sintering because of its unique characteristics compared to conventional sintering methods [3]. FLA uses instantaneous high current to generate intensive pulsed light (IPL), and irradiate IPL toward the specimen to sinter the materials. Unlike the conventional sintering methods, this novel method has lots of advantages including availability of treatment at STP and fast sintering time (~ a few ms). Rapid sintering process gives no time for the diffusion at the interface, thus the interfacial resistance between cathode and LLZO solid-electrolyte must be reduced. We fabricated LLZO solid-electrolyte on the commercial LiCoO 2 pellet by using solution-based spin-coating method and sintered the film by using FLA method. XPS and energy-dispersive X-ray spectroscopy (EDX) analysis were conducted to observe interface and diffusion of La and Co elements. Also, X-ray diffraction (XRD) method was used to investigate sintering ability of FLA through crystallinity development. The interfacial resistance between LiCoO 2 and LLZO solid-electrolyte was analyzed by electrochemical impedance spectroscopy (EIS) through cross-plane set-up.

Fabrication of porous LLZO solid electrolyte based on modified kapok fiber

Fabrication of Li7La3Zr2O12 Fibers Using Bio-Mass Template Kapok

Preparation of high ionic conductivity composite solid electrolyte with in-situ synthesis of LLZO@ZiF-67

Scalable Freeze Tape Casting Fabrication and Pore Structure Analysis of 3D LLZO Solid-State Electrolytes.

In-situ Li2O-atmosphere Assisted Solvent-Free Route to Produce Highly Conductive Li7La3Zr2O12 Solid Electrolyte

A Simple and Highly Efficient Method toward High-Density Garnet-Type LLZTO Solid-State Electrolyte

Developing Preparation Craft Platform for Solid Electrolytes Containing Volatile Components: Experimental Study of Competition between Lithium Loss and Densification in Li7La3Zr2O12

Elastic and well-aligned ceramic LLZO nanofiber based electrolytes for solid-state lithium batteries

Manipulating Li2O atmosphere for sintering dense Li7La3Zr2O12 solid electrolyte

Crystal Structure and Preparation of Li7La3Zr2O12 (LLZO) Solid-State Electrolyte and Doping Impacts on the Conductivity: An Overview

Enhanced electrochemical performance of solid PEO/LiClO4 electrolytes with a 3D porous Li6.28La3Zr2Al0.24O12 network

A novel method for preparation of high dense tetragonal Li7La3Zr2O12

Synthesis of Li7La3Zr2O12 Solid Electrolyte by Solid Phase Sintering Method

Ultrafast-sintered self-standing LLZO membranes for high energy density lithium-garnet solid-state batteries

Processing and Properties of Garnet‐Type Li7La3Zr2O12 Ceramic Electrolytes

Study of a composite solid electrolyte made from a new pyrrolidone-containing polymer and LLZTO

Fast and low-temperature densification of highly conductive Li7La3Zr2O12 ceramic electrolytes for solid-state batteries

Highly conductive thin lamellar Li7La3Zr2O12/Li3InCl6 composite inorganic solid electrolyte for high-performance all-solid-state lithium battery

(Invited) Advancing Understanding of Composite Polymer Electrolytes with LLZO Nanofibers

Key factors of the self-consolidation mechanism for sintering Li7La3Zr2O12 solid electrolytes

A Study on Cathode Interface of Li-La-Zr-O Solid-State Electrolyte Fabricated Via Rapid Sintering Process