Abstract:To adequately develop the application of marine resources for island construction and sustainability in the construction industry, this paper explores the feasibility of using alkali-activated materials (AAMs) as alternatives to ordinary Portland cements (OPCs) for the application in seawater coral aggregate concrete (CAC) structures. Artificial seawater, coral aggregates, and slag-based AAMs containing 5 wt.% silica fume and 15 wt.% fly ash, were mixed to develop the alkali-activated seawater coral aggregate concrete (AACAC), with the workability (slump), compressive and splitting tensile strengths being studied. The influence parameters, such as the total cementitious material content, water-to-binder ratio, and sand rate, were considered through Taguchi orthogonal experimental design method. The experimental results indicated that the most important factor herein for the compressive and splitting tensile strengths of the AACAC was the total cementitious material content. The analysis of range and variance demonstrated that an optimal mixture for AACAC was determined to be a total cementitious material content of 500 kg center dot m(-3), a water-to-binder ratio of 0.60, and a sand rate of 55%. Then, this optimal mixture was adopted to analyze the effect of the replacement ratio of sea sand for coral sand (R-s) on the workability, compressive and splitting tensile strengths of AACAC, and the cement-based CAC was selected as the reference. Finally, the microstructures of the paste-aggregate interface for the CAC and AACAC sliced specimens were detected by scanning electron microscopy (SEM). It can be concluded that increasing R-s improved the workability of the AACAC, but exhibited a very slight effect on its mechanical properties. Additionally, the utilization of AAMs can effectively reduce the broken of the coral aggregate inside the concrete due to improved interfacial transition zone (ITZ) between the aggregates and the pastes, thereby exhibiting a higher splitting tensile strength than that of the cement-based CAC.

Progresses of high-performance coral aggregate concrete (HPCAC): A review

Advances in coral aggregate concrete and its combination with FRP: A state-of-the-art review

Mechanical Behavior and Durability of Coral Aggregate Concrete and Bonding Performance with Fi Ber-Reinforced Polymer (FRP) Bars: A Critical Review

Durability of Seawater Coral Aggregate Concrete under Seawater Immersion and Dry-Wet Cycles

Effect of Aggregate Size on the Axial Compressive Behavior of FRP-Confined Coral Aggregate Concrete

Strength and Fracture Properties of Coral Concrete under Impact of Coral Aggregate Type and Fiber Hybridization

Mechanical Properties and Durability of FRP-reinforced Coral Aggregate Concrete Structures: A Critical Review

Compressive Stress-Strain Behavior of Seawater Coral Aggregate Concrete Incorporating Eco-Efficient Alkali-Activated Slag Materials

Design and properties of seawater coral aggregate alkali-activated concrete

Mesoscopic study of the mechanical properties of coral aggregate concrete under complex loads

Constitutive Relations of Coral Aggregate Concrete under Uniaxial and Triaxial Compression

Towards Enhancing the Durability of Seawater Coral Aggregate Concrete under Drying-Wetting Cycles with Slag-Based Geopolymers

Optimization of Mix Proportion of Basic Magnesium Sulfate Cement-Based High-Strength Coral Concrete

3D mesoscopic analysis on the compressive behavior of coral aggregate concrete accounting for coarse aggregate volume and maximum aggregate size

Design and Evaluation of an Ultrahigh-Strength Coral Aggregate Concrete for Maritime and Reef Engineering

A Gentle Acid-Wash and Pre-Coating Treatment of Coral Aggregate to Manufacture High-Strength Geopolymer Concrete

Enhancing Mechanical Performance and Crack Morphology of Engineered Cementitious Composites Through Tailoring Coral Sand

Investigation on Chloride Releasing from Coral Aggregates to Cement Paste in Coral Aggregate Concrete

Experimental study on mechanical properties and durability of basalt fiber reinforced coral aggregate concrete

Mechanical Properties and Drying Shrinkage of Alkali-Activated Seawater Coral Aggregate Concrete

Axial Compressive Behavior of GFRP-confined Seawater Coral Aggregate Concrete Incorporating Slag-Based Alkali-Activated Materials