Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

Formation of fine granular area in a non‐defect matrix of austenitic stainless steel during very high cycle fatigue

Fine granular area formation by damage‐induced shear strain localization in very‐high‐cycle fatigue

Mechanism of fine granular area and white etching crack formation in AISI 52100 bearing steel

On the Formation of GBF of High-Strength Steels in the Very High Cycle Fatigue Regime

Residual stress induced granular bright facets around inclusions in high-strength steels under high-cycle fatigue

Microstructure Refinement and Grain Size Distribution in Crack Initiation Region of Very-High-cycle Fatigue Regime for High-Strength Alloys

1216 Nano-Scale Strength Analysis by EBSD and AFM Hybrid Method in Ultrafine-Grained Copper Processed by ECAP

Fatigue Crack Growth Behavior of a Coarse- and a Fine-Grained High Manganese Austenitic Twin-Induced Plasticity Steel

Effect of ultrasonic peening treatment on the fatigue behaviors of a magnesium alloy up to very high cycle regime

Microstructural Evolution and Formation of Fine Grains During Fatigue Crack Initiation Process of Laser Powder Bed Fusion Ni-based Superalloy

Effects of local microstructure on crack initiation in super martensitic stainless steel under very-high-cycle fatigue

Non-inclusion induced crack initiation in multiphase high-strength steel during very high cycle fatigue

Nanoprecipitates assisting subsurface cracking in high-strength steel under very high cycle fatigue

Effects of microstructure on crack initiation in super martensitic stainless steel under very‐high‐cycle fatigue at elevated temperature

High-cycle-fatigue Induced Continuous Grain Growth in Ultrafine-Grained Titanium

Grain refinement and microstructural evolution of grain boundary allotriomorphic ferrite/granular bainite steel after prior austenite deformation

Fatigue Life and Mechanistic Modeling of Interior Micro-Defect Induced Cracking in High Cycle and Very High Cycle Regimes

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

In-situ SEM-EBSD investigation of the low-cycle fatigue deformation behavior of Inconel 718 at grain-scale

Inter- And Intra-Agglomerate Fracture In Nanocrystalline Nickel

Further Investigation on Microstructure Refinement of Internal Crack Initiation Region in VHCF Regime of High-Strength Steels