Abstract:In this study, dissimilar structures of 316L and Inconel 625 were fabricated using wire and arc additive manufacturing with the cold metal transfer plus pulse mode (CMT+P). Based on various arc scanning strategies, including single-layer and multi-layer deposition, in vertical and horizontal building directions, the evolution of interface microstructure and mechanical properties of additively manufactured heterogeneous structures were studied. The microstructure analysis showed that during single-layer deposition, both 316L and Inconel 625 formed dendrites and columnar crystals. During the multi-layer deposition process, the 316L material solidified to form a dual-phase microstructure consisting of austenite and ferrite, whereas the Inconel 625 primarily formed an austenite microstructure. The segregation of elements such as Nb and Mo occurred at the interface, resulting in the formation of numerous precipitated phases at the grain boundary. At the interface of the vertically deposited sample, the inadequate diffusion of elements resulted in the formation of a transition layer in the microstructure. The microhardness of the deposited Inconel 625 layer was approximately 215 HV, while the microhardness of the deposited 316L layer ranged from 170 to 200 HV. The tensile strength and elongation rate of the horizontally deposited samples were higher than those of the vertically deposited structure. Both the tensile strength and elongation rate of the multilayer deposited structure were reduced due to the presence of numerous interfaces. The maximum tensile strength and elongation rate of horizontal single-layer samples were 488.57 MPa and 43.53%, respectively. The average tensile strength and elongation of vertical multi-layer samples were 387.26 MPa and 17.79%, respectively. Results showed that the mechanical properties of the SS316L/Inconel 625 heterogeneous structure in wire and arc additive manufacturing are clearly influenced by the deposition strategies and interface orientation.

Study on the droplet transfer behavior and microstructure of wire arc additive manufactured Inconel 718 alloy assisted by an alternating magnetic field

Surface Morphology Refinement and Laves Phase Control of Plasma Arc Additively Manufactured Inconel 718 Via an Alternating Magnetic Field

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Enhanced Comprehensive Properties of Directed Energy Deposited Inconel 718 by a Novel Integrated Deposition Strategy

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Microstructure and Mechanical Properties of Thick‐Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

A Study on Microstructure and Mechanical Properties of Inconel 718 Superalloy Fabricated by Novel CMT-WAAM Process

Effect of Thermal-Hydrodynamic Coupling Energy on the Processing of Inconel 718 Superalloy

Study on Microstructure and Thermal Cracking Sensitivity of Deposited Ti6Al4V/Inconel 718 Composites Made by Two-Wire Arc Additive Manufacturing by Current

Technology Development for Producing Inconel 625 in Aerospace Application Using Wire Arc Additive Manufacturing Process

Effects of Deposition Strategies on Microstructure and Mechanical Properties of 316L Stainless Steel and Inconel 625 Alloy Dissimilar Structure Fabricated by Cold Metal Transfer Arc Additive Manufacturing

A Quantitative Approach to Precipitate Characterization in Wire Arc Additive Manufactured Inconel 600 Series Alloys

Research on microstructure and mechanical properties of hybrid plasma arc and micro-rolling additive manufacturing of Inconel 718 superalloy

Location-dependent microstructure analysis and mechanical behavior of inconel 625 using Cold Metal Transfer(CMT) based wire and arc additive manufacturing

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Effect of Hot-Wire Method on Microstructure and Mechanical Properties of Wire Arc Additive Repaired Superalloy.

Investigation of Single and Double Pulse Techniques on Microstructure and Mechanical Anisotropy of Inconel 686 Component Fabricated by Wire Arc Directed Energy Deposition

Microstructure, texture and mechanical properties of Inconel GH4169 superalloy fabricated by wire arc additive manufacturing with arc oscillation

Comparative investigation of wire arc additive manufacturing of Al-5%Mg alloy with and without external alternating magnetic field