Abstract:The laser hot-wire (LHW) process has the potential to deposit material at high rates using low laser power. An LHW experiment was designed to be able to deposit material at the rate of 3.46 kg per hour with less than 10 kW of laser power. Four thermocouples were built into the substrate to record the temperature variation during the deposition. The results show that temperature fluctuates in a periodic manner with the deposition layer by layer. Simultaneously, the distortion of the substrate was measured. The substrate is distorted, and the maximum distortion increases gradually during deposition.The equivalent heat conduction coefficient for heat convection in the molten pool is discussed. It becomes apparent that the heat convection of flowing molten metal is 3-5 times that of molten metal at rest. The absorptivity of laser power was determined by comparison between the simulation and a one-pass cladding experiment. The absorptivity of laser power is approximately 15% in this experiment.Numerical simulation of LHW additive manufacturing was conducted to obtain the temperature, stress and strain fields, and the distortion. The outstanding features for numerical simulation are additive geometry and numerous analysis steps. The INP files of ABAQUS are compiled in a Matlab program because of the considerable number of steps and element definitions. Temperature variation and substrate distortion are both measured to validate the FEA model. The verification result indicates that the LHW model is feasible and accurate.The maximum residual stress is located in the junction between the deposit and substrate when the deposition is finished. This junction area becomes the most likely crack position. Deposited material undergoes complicated thermal cycles during the LHW process. Temperature variation determines the phase transformation. The microstructure change of the heat affected zone was analyzed on the basis of computational temperature variation. Such interpretation can effectively explain softened area in the heat affected zone of the substrate. A numerical computation method is used to map the processing window of stable hot-wire deposition. It is shown that the stable deposition has top and bottom limitations under a certain current intensity and wire feed speed. (C) 2016 Elsevier B.V. All rights reserved.

Improving the deposition efficiency and mechanical properties of additive manufactured Inconel 625 through hot wire laser metal deposition

Highly-efficient additive manufacturing of Inconel 625 thin wall using hot-wire laser metal deposition: Process optimization, microstructure, and mechanical properties

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

Influence of Interlayer Temperature on Microstructure and Mechanical Properties of Additively Manufactured Inconel 625

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology

Experimental Study and Modeling of H13 Steel Deposition Using Laser Hot-Wire Additive Manufacturing

Effect of Welding Torch Mode on Heat Input, Microstructure, and Mechanical Performance of Inconel 625 via Wire‐Arc‐Directed Energy Deposition

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Microstructure and Mechanical Properties of Thick‐Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths

CMT-based wire arc additive manufacturing of Inconel 625 alloy

Microstructures and Mechanical Behaviors of Additive Manufactured Inconel 625 alloys via Selective Laser Melting and Laser Engineered Net Shaping

Effect of Functionally Graded Material (FGM) Interlayer in Metal Additive Manufacturing of Inconel-Stainless Bimetallic Structure by Laser Melting Deposition (LMD) and Wire Arc Additive Manufacturing (WAAM)

Comparison of microstructure features and mechanical properties for additive manufactured and wrought nickel alloys 625

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Effect of heat treatment on microstructure, precipitation behavior and mechanical properties of Inconel 718 fabricated by laser direct energy deposition

Intergranular corrosion characteristics of high-efficiency wire laser additive manufactured Inconel 625 alloys

Microstructural evolution and mechanical properties of Inconel 625 superalloy fabricated by pulsed microplasma rapid additive manufacturing

Overcoming machining challenges in hybrid laser metal deposition of IN718 with heat-assisted minimum quantity lubrication

The effect of interval pulsed laser deposition on the microstructure and mechanical properties of Inconel 718 parts using laser directed energy deposition

Effect of Welding Speed on Microstructure and Mechanical Properties of Selective Laser Melting Inconel 625 Alloy Laser Welded Joint