Abstract:The hot deformation behavior of a FeCoCrNi high-entropy alloy was investigated in this work. The tests were carried out at 900–1100 o C, under strain rates of 0.001–0.1 s -1 and the effect of friction between specimen and tool on flow stress curves under different deformation conditions was analyzed and modified. The experimental results were employed to determine the constitutive equation with strain-dependent material constants for modeling and for prediction of flow stress at different deformation conditions, using the data obtained from the Sellars–Tegart–Garofalo equation. Microstructural studies revealed that dynamic recrystallization was the primary softening mechanism, resulting in significant microstructural reconstitution and fine grains formation. A complete-recrystallized microstructure with a high proportion of annealing twin boundary was obtained in the specimen hot compressed at 1000 o C/0.01 s -1 , so that the average grain size was 22 μm, compared to the initial grain size of 42 μm. The increase of the size and fraction of the DRXed grains during hot deformation decrease the alloy hardness. The dynamic recrystallization parameters such as critical, peak, and steady-state stress, and strain were determined using the work hardening rate analysis. Moreover, the activation energy for deformation of the alloy was determined to be 417 kJ mol -1 . The results also indicated that the critical stress and strain for initiating dynamic recrystallization were inversely proportionate to deformation temperature and the strain rate. Furthermore, increasing the deformation temperature resulted in grain growth, whereas increasing the strain rate led to grain refinement. The critical stress and strain were dependent on the Zener–Hollomon ( Z ) parameter via a power relation with exponents of 0.14 and 0.12, respectively.

Effect of High Temperature Deformation on the Low Thermal Expansion Behavior of FE-29%NI-17%CO Alloy

Investigation of Temperature-Dependent Magnetic Properties and Coefficient of Thermal Expansion in Invar Alloys

Investigation on the thermal expansion behavior of FeCoNi and Fe30Co30Ni30Cr10-xMnx high entropy alloys

High temperature deformation mechanism and microstructural evolution of relatively lightweight AlCoCrFeNi high entropy alloy

The Effects of Refractory Elements on Mechanical Properties in CoCrNiFe Concentrated Solid Solution Alloys Across Different Temperatures

On Zero or Negative Thermal Dilatation and Phase Transformations in Cold-Worked Fe–Ni Invar Alloys

Hot deformation behavior and workability of a Ni–Co based superalloy

Dynamic Recrystallization Behavior of the Equiatomic FeCoCrNi High-Entropy Alloy during High Temperature Deformation

Effect of Heat Treatments on Magnetic Properties and Thermal Expansion Behavior in Two Distinct Types of Fe-Ni Invar Alloys

Regulation of the Concentration Heterogeneity and Thermal Expansion Coefficient in the Metastable Invar FeNi31.1 Alloy

Temperature-dependent hardening contributions in CrFeCoNi high-entropy alloy

Hot Deformation Behavior and Microstructure Evolution of Cu–Ni–Co–Si Alloys

Invar Effect in the Wide and Higher Temperature Range by Coherent Coupling in Fe‐Based Alloy

Microstructure Evolution of a Ti–Al–Sn–Zr Based Alloy During the Hot Compression Deformation

Hot deformation behavior and mechanism of cold deformed CoCrCu1.2FeNi high entropy alloy

High Temperature Tensile Deformation Behavior of New Heat Resistant Aluminum Alloy

The Temperature Dependence of High-Temperature Strength and Deformation Mechanism in a Single Crystal CoNi-base Superalloy

High-temperature deformation behavior of a novel high strength and high elasticity Cu–20Ni–20Mn–0.3Nb–0.3Cr–0.1Zr alloy

Elucidating the warm compression of CoCrCuFeNi high entropy alloy: Modeling and microstructural evolution

Effect of Cold-Drawn Deformation on Microstructure and Properties of Invar Alloy Wires

Effect of initial microstructure on grain refinement under hot compression in CrMnFeCoNi high-entropy alloy with Al addition