Abstract:Purpose Polyetheretherketone (PEEK) is used to manufacture biomedical implants because it has a high strength-to-weight ratio and high strength and is biocompatible. However, the use of fused deposition modeling to print a PEEK results in low strength and crystallinity. This study aims to use the Taguchi method to optimize the printing factors to obtain the highest tensile strength of the printed PEEK object. The annealing effect on printed PEEK object and crystallinity are also investigated. Design/methodology/approach This study determines the printing factors including the printing speed, layer thickness, printing temperature and extrusion width. Taguchi experimental design with a L9 orthogonal array is used to print the tensile specimen and carried out the tensile test to compare the tensile strength and porosity. Analysis of variance (ANOVA) is used to determine the experimental error and to determine the optimization printing parameters to obtain the highest tensile strength. A multivariate linear regression analysis is used to obtain the linear regression equation for predicting the theoretical tensile strength. An X-ray analysis is achieved to evaluate the crystalline of printed object. The effect of annealing is investigated to improve the tensile strength of printed part. An intervertebral lumber device is printed to demonstrate the feasibility of the obtained optimization parameters for practical application. Findings Taguchi experiment designs nine sets of parameters to print the PEEK tensile specimen. The experimental results and the ANOVA present that the order in which the factors affect the tensile strength for printed PEEK parts is the layer thickness, the extrusion width, the printing speed and the printing temperature. The optimized printing parameters are a printing speed of 5 mm/s, a layer thickness of 0.1 mm, a printing temperature of 395 °C and an extrusion strand width of 0.44 mm. The average tensile strength of printed specimen with the optimized printing parameters is 91.48 MPa, which is slightly less than the theoretical predicted value of 94.34 MPa. After annealing, the tensile strength increases to 98.85 MPa, which is comparable to that for molded PEEK and the porosity decreases to 0.3 from 3.9%. X-ray diffraction results show that all printed and annealed specimens have a high degree of crystallinity. The printed intervertebral lumber device has ultimate compressive load of 13.42 kN. Originality/value The optimized printing parameters is suitable for low-price fused deposition modeling machine because it does not involve a table at high temperature and can print the PEEK object with high tensile strength and good crystalline. Annealing parameters offer a good solution for tensile strength improvement.

Optimization of material extrusion additive manufacturing process parameters for polyether ketone ketone (PEKK)

Effects of 3D Printing Parameters on the Flexural Properties of Semi-Crystalline PEKK

EFFECTS OF EXTRUSION RATE AND POST-ANNEALING ON MECHANICAL PROPERTIES AND PRINTING QUALITY OF ADDITIVELY MANUFACTURED CARBON FIBER REINFORCED POLYETHERKETONEKETONE (PEEK) PARTS

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone

Experimental investigation of process parameters in polyether ether ketone 3D printing

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

Optimization of fused deposition modeling process parameters using the Taguchi method to improve the tensile properties of 3D-printed polyether ether ketone

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Research on the Fused Deposition Modeling of Polyether Ether Ketone

Effect of FFF process parameters on mechanical strength of CFR-PEEK outputs

An overview on the influence of process parameters through the characteristic of 3D-printed PEEK and PEI parts

Optimization of Flexural Performance of PETG Samples Produced by Fused Filament Fabrication with Response Surface Method

Polyether Ketone Ketone (PEKK) matrix composites for material extrusion additive manufacturing

Increasing the Isotropy of 3D Printed Poly(ether ether ketone) Using a Combination of Bimodal Polymer Blends and Post-Process Thermal Annealing

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Optimization of Fused Deposition Modeling Process Parameters and Dynamic Mechanical Analysis of 3D Printed Polycarbonate/Acrylonitrile-Butadiene-Styrene Composite Loaded with Tetrabromobiphenol-A and Microcrystalline Cellulose

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Optimization of FDM 3D printing parameters for high strength PEEK using the Taguchi method and experimental validation

Effects of printing parameters on the mechanical characteristics and mathematical modeling of FDM-printed PETG

Optimizing the flexural properties of additively manufactured PETG: a multi-objective approach

Comparative Study of the Sensitivity of PLA, ABS, PEEK, and PETG’s Mechanical Properties to FDM Printing Process Parameters