Abstract:The geometric parameters and stress conditions of fractures are the main factors that determine the strength and deformation characteristics of fractured rock masses, and the ultimate instability and failure of fractured rock masses are caused by the extension and penetration of the structural plane. In this study, a series of Φ50 × 100 mm standard cylinder specimens were prepared to simulate brittle rock masses. The uniaxial compressive strength and tensile strength of the specimens were 33 and 2.8 MPa, respectively. Non-persistent fractures with different inclination angles, connectivity rates, openings, spacings, groups, and roughness were prefabricated in the specimens, and the fractures were filled with plasticine. Furthermore, the crack propagation and failure mechanisms of filled fractured rock masses under uniaxial compression (the loading rate is 0.2 MPa/s) were analyzed by a 3D video image correlation system. Comparing the results of this research with those of previous researches, and combining with relevant theoretical analysis, the following conclusions are drawn: (1) the curve of the peak strength reduction coefficient k σ of the specimen with the fracture inclination angle α is roughly V-shaped, and being the smallest when the fracture inclination angle α is 45°; the reduction coefficient k is monotonically decreasing with the three groups of fracture geometric parameters of spacing b , connectivity rate μ , and opening d , and the peak strength reduction coefficient k σ of the specimen is typically smaller than the elastic modulus reduction coefficient k E . (2) The post-peak stress–strain curve of the specimen with filled fractures is relatively slow, and the plasticity is obviously enhanced. The geometric parameters of the fractures are important factors affecting the change of the mechanical properties of the specimen. The influence degree of different fractures geometric parameters on rock masses mechanical properties is as follows: fracture sets > spacing > connectivity rate > inclination angle > opening > roughness. (3) Due to the concentration of stress, cracks first initiate from the fracture tips, then propagate parallel to the loading direction, and ultimately coalesce between the fractures and the specimen surface. During the failure process of the specimens, four types of cracks were observed: tensile cracks, shear cracks, wing cracks, and reverse wing cracks, with wing cracks dominating crack propagation. (4) Compared with the specimens with unfilled fractures, the stress concentration at the filled fractures was reduced, and more microcracks with higher dispersion developed around the filled fracture.

Influence of polymeric resin-infilling on onset and fracture growth along wing trajectory in open-flawed sandstone specimen

Discrete element modeling on crack evolution behavior of sandstone containing two oval flaws under uniaxial compression

Experimental and Theoretical Study on Crack Growth Using Rock-Like Resin Samples Containing Inherent Fissures and its Numerical Assessment

Investigation on Fracture Mode and Initiation Mechanisms of Cracks in Sandstone Disk Containing a Preexisting Flaw

Stress Evolution of Rock-Like Specimens Containing a Single Fracture Under Uniaxial Loading: a Numerical Study Based on Particle Flow Code

Failure and Mechanical Behaviors of Sandstone Containing a Pre-existing Flaw Under Compressive–shear Loads: Insight from a Digital Image Correlation (DIC) Analysis

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

Experimental Study on the Effects of Geometric Parameters of Filled Fractures on the Mechanical Properties and Crack Propagation Mechanisms of Rock Masses

In-Plane fracture of laminated fiber reinforced composites with varying fracture resistance: experimental observations and numerical crack propagation simulations

Experimental study of the effect of crack distribution on the failure mechanism of sandstone specimens based on inclination angles and number of parallel flaws

Development and Evaluation of Methods of Plane Stress Fracture Analysis. Part 3. Application of the Residual Strength Prediction Technique to Complex Aircraft Structure

Experimental multi-scale characterization of mode-II interlaminar fracture in geometrically scaled stitched and unstitched resin-infused composites

Failure Behavior of Sandstone Specimens Containing a Single Flaw Under True Triaxial Compression

The influence of infilling material strength on mechanical properties and failure mechanism of fractured sandstone

Cracking and Stress–Strain Behavior of Rock-Like Material Containing Two Flaws Under Uniaxial Compression

Mixed mode embedded circular delamination propagation in spar wingskin joint made with curved FRP composite laminates

Fracture behavior of sandstone with partial filling flaw under mixed-mode loading: Three-point bending tests and discrete element method (DEM) numerical approach

A Numerical Investigation of Fracture Infilling and Spacing in Layered Rocks Subjected to Hydro-Mechanical Loading

Effects of infilling materials on mechanical behaviors and cracking process of pre-cracked rock: Insights from a hybrid continuum-discontinuum method

Effect of Confining Pressure and Strain Rate on Mechanical Behaviors and Failure Characteristics of Sandstone Containing a Pre-existing Flaw

Experimental and DEM study on failure behavior and stress distribution of flawed sandstone specimens under uniaxial compression