Abstract:Hydrodynamic model tests and numerical simulations may be combined in a complementary manner during the design and qualification of new offshore structures. In the EU H2020 project LIFES50+ (lifes50plus.eu), a model test campaign of floating offshore wind turbines using Real-Time Hybrid Model (ReaTHM) testing techniques was carried out at SINTEF Ocean in fall 2017. The present paper focuses on the process of calibrating a numerical model to the experimental results. The concepts tested in the experimental campaign was a 1:36 scale model of the public version of the 10MW OO-Star Wind Floater semi-submersible offshore wind turbine. A time-domain numerical model was developed based on the as-built scale model. The hull was considered as rigid, while bar elements were used to model the mooring system and tower in a coupled finite element approach. First-order frequency-dependent added mass, potential damping, and excitation forces/moments were evaluated across a range of frequencies using a panel method. Distributed viscous forces on the hull and mooring lines were added to the numerical model according to Morison’s equation. Potential difference-frequency excitation forces were also included by applying Newman’s approximation. The quasi static properties of the mooring system were assessed by comparing the restoring force and maximum line tension with the pull-out test. Drag coefficients for the line segments were estimated by imposing the measured fairlead motion from model tests as forced displacement and comparing the calculated and measured dynamic line tension. The linear and viscous damping coefficients were first estimated based on the decay tests, and the tuned damping coefficients were compared to initial guesses based on the Reynolds and Keulegan-Carpenter number at model scale. The results were then applied in the numerical model, and simulations in extreme irregular waves were compared to the experiments. It was found that second order drift forces proved to be significant, particularly for the severe irregular seastate. These could not be modelled correctly applying the potential drift forces together with quadratic damping matrix tuned to the free decay test. And the model with viscous drag coefficients tuned to decay tests also underestimated the slow drift motions. Thus, new viscous drag coefficients were determined to match the low frequency platform response. To inverstigate the performance of the tuned model, comparisons were made for a moderate seastate and for a simulation with both waves and wind on an operating turbine. In the end, possible further improvements to the modelling were suggested.

Sail assist developments 1979–1985

An assisted propulsion device of vessel utilizing wind energy based on Magnus effect

Wing Sails: Numerical Analysis of High-Performance Propulsion Systems for a Racing Yacht

Circulation-controlled wind-assisted ship propulsion: Technical innovations for future shipping industry decarbonization

Model Analysis of Green Water Phenomena and Loading for Ship Sailing with Slow Speed

Analysis of Dynamic Characteristics of Rotor Sail Using a 4DOF Rotor Model and Finite Element Model

Computational Fluid Dynamics Investigation of the Spacing of the Aerodynamic Characteristics for Multiple Wingsails on Ships

Propeller and Engine Performance of Commercial Windships: Benefits and Trade-Offs

EXPERIENCES OF ROTOR SAIL INSTALLATIONS ON VARIOUS SHIP TYPES AND THE EMISSION REDUCTION POTENTIAL OF ROTOR SAILS

Investigation of the efficiency of wind-assisted systems using model-based design approach

Experimental Comparison of Three Floating Wind Turbine Concepts

Wingsail performance in unsteady atmospheric surface layer winds

Low-Height Lifting System for Offshore Wind Turbine Installation: Modelling and Hydrodynamic Response Analysis Using the Commercial Simulation Tool SIMA

On the performance of marine propeller in regular waves, Part I: Single Blade loads in moderate sea states

Fluid Dynamic Simulation of Sail Design Performance on Sail-Assisted Ship; A Preliminary Study

Wind Tunnel Experiment of Multi-Mode ARC Sail Device

Floating Wind Turbine Model Test to Verify a moordyn Modification for Nonlinear Elastic Materials

Distinctive Features of Using the Propulsor of the Underwater Sail Type and the Direct-Flow Wave Propulsor on a Semisubmerged Catamaran

Numerical investigation on the effects of heel on the aerodynamic performance of wing sails

Calibration of Hydrodynamic Coefficients for a Semi-Submersible 10 MW Wind Turbine

Experimental and numerical investigation of a taut-moored wave energy converter: a validation of simulated mooring line forces