Abstract:Ultra-thin flexible photovoltaic materials for solar cells, like transition metal di-chalcogenides (TMDCs), hold significant promise due to their advantageous properties in photon absorption and electronic transport, being composed of atomically thin 2D layered semiconductor materials. An essential 2D-layered substance, tungsten Disulfide (WS2), classified as a TMDC, has garnered substantial attention due to its notable chemical and physical characteristics. This work presents a novel method for getting good photovoltaic results using WS2 solar cells. The suggested configuration "Al/FTO/SnS2/WS2/CuO/Ni" comprises two absorber layers, which involves incorporating CuO as a supplementary absorber layer and SnS2 as the buffer layer. Several metals with varying work functions were investigated one at a time, therefore, Al and Ni were chosen for the front as well as back contact in order to produce a low resistance metal-semiconductor (M-S) interface. Additionally, aluminum (Al) and nickel (Ni), are commonly used due to their well-understood properties such as conductivity and thermal stability. Subsequently, an analysis was conducted to determine the effects of important influencing factors, such as operating temperature, layer thickness, defects density, and doping density of the absorber and buffer layers. The power conversion efficiency (PCE) was achieved approximately 30%, accompanied by an open circuit voltage (VOC) of 1.02 V, a short circuit current (JSC) of 34.35 mA/cm2, and a fill factor (FF) of 87.27%. This improvement was achieved by utilizing an Al/FTO/SnS2/WS2/CuO/Ni heterostructure. In comparison, the reference cell without CuO (single absorber) had a PCE of 21.74%, VOC of 0.88 V, JSC of 28.6 mA/cm2, and FF of 86.23%. The results obtained from an extensive numerical analysis and demonstrate the immense potential of the SnS2/WS2/CuO heterostructure, indicating a promising direction for the manufacturing of photovoltaic and photonic devices based on WS2-TMDCs. This study provides a systematic roadmap for the fabrication process as well as realization of low-cost high efficiency solar cell.

Solution-processed CuSCN/WS2 hole transport layer for enhancing efficiency of organic solar cells

A Low-Temperature Solution-Processed CuSCN/Polymer Hole Transporting Layer Enables High Efficiency for Organic Solar Cells

Novel 2D material from AMQS-based defect engineering for efficient and stable organic solar cells

Cl 2 -Doped CuSCN Hole Transport Layer for Organic and Perovskite Solar Cells with Improved Stability

High-quality WS2 Film As a Hole Transport Layer in High-Efficiency Non-Fullerene Organic Solar Cells

All-Inorganic Hydrothermally Processed Semitransparent Sb 2 S 3 Solar Cells with CuSCN as the Hole Transport Layer

High-performance hole transport layer based on WS2 doped PEDOT:PSS for organic solar cells

CuSCN as Hole Transport Material with 3D/2D Perovskite Solar Cells

Design and optimization of WS2 based high performance double absorber solar cell

Solution-Processed Cu9S5 As a Hole Transport Layer for Efficient and Stable Perovskite Solar Cells.

Co‐Solvent Assisted Optimization of the CuSCN Hole Transport Layer for Enhancing the Efficiency of Ambient Processable Perovskite Solar Cells with Carbon Counter Electrodes

Chemisorption-Induced Robust and Homogeneous Tungsten Disulfide Interlayer Enables Stable PEDOT-Free Organic Solar Cells with Over 19% Efficiency

High-efficiency solution-processed CdTe nanocrystal solar cells incorporating a novel crosslinkable conjugated polymer as the hole transport layer

Solvent‐Induced Copper Vacancy in CuSCN Layer: A Strategy to Boost Conductivity and Optimize Energy Levels for Efficient Organic Solar Cells

Self-assembled hole-transporting material constructed by chlorination and conjugation strategies toward the efficient organic solar cells

7.5% n-i-p Sb2Se3 solar cells with CuSCN as hole-transport layer

Kesterite Cu2znsns4 As A Low-Cost Inorganic Hole-Transporting Material for High-Efficiency Perovskite Solar Cells

Solution-processed tungsten diselenide as an inorganic hole transport material for moisture-stable perovskite solar cells in the n-i-p architecture

Solution-processed and thickness-insensitive hole transport layer for high efficiency organic solar cells

Efficient Hole Transport Layer for Organic Solar Cell Based on Exfoliated-MoS 2 Doped PEDOT

Performance Enhancement of Evaporated CsPbI2Br Perovskite Solar Cells with a CuSCN Hole Transport Layer Via a Cesium Bromide Buffer Layer