Abstract:Perovskite solar cells have attracted extensive attention because of their photoelectric characteristics. Since 2009, the photoelectric conversion rate of the solar cells has soared from 3.8% to 25.7%. Perovskite material has become a focus of extensive academic research due to its advantages of high carrier mobility, low exciton binding energy, wide absorption spectrum and high optical absorption coefficient. However, organic P-type semiconductor material is usually used as a hole transport layer in high efficiency perovskite solar cells, for example, Spiro-OMeTAD, PEDOT:PSS, and PTAA. Because Spiro-OMeTAD is difficult to purify, many hole transport materials containing triphenylamine like Spiro-OMeTAD have been synthesized, such as triphenylamine polymer PTAA. As the conjugate parts of these triphenylamine transport materials are not coplanar and the space is distorted, they cannot form ordered stacks by spin-coating method, so their charge properties are weak, and li-TFSI and tBP are often added to improve the hole transport, so as to achieve better device effects. Moreover, the PTAA has the problem of infiltration, and it is difficult to form a completely covered perovskite film on it, which seriously affects the quality and surface morphology of perovskite film. The PEDOT:PSS itself has an acidic and corrosive electrode, and is easy to absorb moisture, which will affect the stability of the solar cell. The performance of organic material will deteriorate seriously under environmental factors such as humidity, temperature and UV irradiation, which will accelerate the aging of perovskite solar cells and become one of the main obstacles to their practical applications. In this work, the inorganic cuprous thiocyanate (CuSCN) is used as a hole transport material, the CuSCN is a rich and stable P-type semiconductor material, which has the characteristics of abundance, low cost, high carrier mobility, appropriate energy level, low defect density, good thermal stability, and excellent light transmittance. The CuSCN is one of the few known compounds with both high optical transparency (its wide band gap is 3.7–3.9 eV) and significant P-type electrical conductivity. Most importantly, CuSCN is inexpensive and can be prepared by solution method at room temperature. And its hole transport properties are improved by lithium doping. On this basis, the surface of CuSCN is modified with PTAA to avoid the interaction between CuSCN and lead iodide (PbI 2 ), and the large-grained and dense perovskite films are prepared. Finally, the performance of perovskite solar cells is effectively improved. This work provides a reference for the preparation of the stable and efficient perovskite solar cells.

Solvent‐Induced Copper Vacancy in CuSCN Layer: A Strategy to Boost Conductivity and Optimize Energy Levels for Efficient Organic Solar Cells

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Co‐Solvent Assisted Optimization of the CuSCN Hole Transport Layer for Enhancing the Efficiency of Ambient Processable Perovskite Solar Cells with Carbon Counter Electrodes

Electronic Structure and Surface Properties of Copper Thiocyanate: A Promising Hole Transport Material for Organic Photovoltaic Cells

Antisolvent Treatment on Wet Solution‐Processed CuSCN Hole Transport Layer Enables Efficient and Stable Perovskite Solar Cells

Bidirectional Passivation for Highly Efficient and Stable CuSCN-Based Perovskite Solar Cells Using (3-Mercaptopropyl)trimethoxysilane

A Low-Temperature Solution-Processed CuSCN/Polymer Hole Transporting Layer Enables High Efficiency for Organic Solar Cells

Solution-processed CuSCN/WS2 hole transport layer for enhancing efficiency of organic solar cells

Slot‐Die‐Deposition of CuSCN Using Asymmetric Alkyl Sulfides as Co‐Solvent for Low‐Cost and Fully Scalable Perovskite Solar Cell Fabrication

Efficient Inverted Perovskite Solar Cells with CuSeCN As the Hole Transport Material

Synthesis and Application of a Star-Shaped, Conjugated Oligomer Containing a Spiro(Fluorene-9,9'-Xanthene) Core for Copper(I) Thiocyanate Based Perovskite Solar Cells

Improved electrical properties of cuprous thiocyanate by lithium doping and its application in perovskite solar cells

Realizing Efficient and Stable n-i-p Perovskite Solar Cells with CuSCN Hole Transporting Materials via LiSCN Doping and Interface Modulation

Efficient and Stable CuSCN-based Perovskite Solar Cells Achieved by Interfacial Engineering with Amidinothiourea

Coordination Strategy Driving the Formation of Compact CuSCN Hole‐Transporting Layers for Efficient Perovskite Solar Cells

Novel 2D material from AMQS-based defect engineering for efficient and stable organic solar cells

Effects of Antisolvent Treatment on Copper(I) Thiocyanate Hole Transport Layer in n-i-p Perovskite Solar Cells

Synchronous Regulation of Donor and Acceptor Microstructure using Thiophene‐Derived Non‐Halogenated Solvent Additives for Efficient and Stable Organic Solar Cells

High-efficiency Organic Solar Cells Processed from a Halogen-Free Solvent System

Small-Molecule Copper Chloride Modulating the Buried Interfaces of Perovskite Solar Cells