Abstract:High-manganese steels, due to their unique combination of strength and elongation, have been widely used in aerospace, petrochemical and rail transportation. However, a prevalent challenge in advancing the utilization of high-manganese steel is the need for corresponding welding consumables. The deformation mechanism of high-manganese steel encompasses three primary mechanisms: martensitic phase transformation, twinning and dislocation movement. The stacking fault energy (SFE) is a critical factor in determining the dominant deformation mechanism in high-manganese austenitic steels. Furthermore, the magnitude of the SFE is principally influenced by the alloying elements present and the temperature at which deformation occurs. Alloying elements can significantly influence the microstructure and mechanical properties of wire arc additive manufacturing (WAAM) of high-manganese steels. The metal powder-cored wire of high-manganese steel with full austenitic microstructure was designed in this paper. The effects of C, Mn and Cu on the microstructure, solute segregation and properties of WAAM of high-manganese steels were systematically investigated by optical microscopy, electron microscopy and mechanical testing. The influence of SFE on the microstructure characteristics and work hardening behaviour were also studied. The results showed that as an increase of the C content, the tensile strength and elongation of deposited metals were improved. The corresponding low-temperature impact toughness increased at first and then decreased. The highest value of impact toughness was 68.5 J with 0.79%C. As the Mn increased, the strength decreased, the elongation increased and the low-temperature impact toughness value displayed an initial increase followed by a subsequent decrease. With the increase of Cu, the yield strength and elongation improved significantly. The tensile strength exhibited a marginal initial increase followed by a decrease, whereas the change was not substantial. In contrast, the low-temperature impact toughness value showed a substantial increase followed by a decrease. The developed M3 wire containing 1.10%C-21%Mn-0.3%Cu possessed the optimum performance (yield strength of 551 MPa, tensile strength of 909 MPa, elongation at break of 30.2%, impact toughness value of 57.5J), with the good mechanical stability and low solidification cracking sensitivity.

C-modified stacking-fault networks inducing the excellent strength- plasticity combinations of medium manganese steel by simple two-stage warm rolling without annealing

Stepwise Warm Rolling for Synergistic Strength and Ductility Enhancement in Heterolamellar Medium-Mn Steel

High strength-toughness combination of a low-carbon medium-manganese steel plate with laminated microstructure and retained austenite

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Super-High-Strength and Formable Medium Mn Steel Manufactured by Warm Rolling Process

Microstructural evolution and strain hardening behavior of a novel two-stage warm rolled ultra-high strength medium Mn steel with heterogeneous structures

Upgrade Rolling Based on Ultra Fast Cooling Technology for C-Mn Steel

Design of a high strength, high ductility 12 wt% Mn medium manganese steel with hierarchical deformation behaviour

Unusual step-like stress flow behavior and mechanisms of a 1.3 GPa grade medium-Mn steel with 51.2 % ductility

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

Effect of C-Mn-Cu on microstructure and properties of wire arc additive manufacturing of high-manganese steels

Heterostructure mediated high strength and large ductility in novel medium-Mn steels with low Mn content

Enhanced mechanical properties of a Fe-Mn-Al-C austenitic low-density steel by increasing hot-rolling reduction

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling

High strength and ductility combination in nano-/ultrafine-grained medium-Mn steel by tuning the stability of reverted austenite involving intercritical annealing

Austenite Tailoring for Strength and Ductility Enhancement in Medium Mn Steel: A Brief Review