Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

High strength-toughness combination of a low-carbon medium-manganese steel plate with laminated microstructure and retained austenite

Low Density High Strength and High Toughness Steel with Ferrite and Martensite Laminated Structure

The combination of strength and cryogenic impact toughness in low carbon 5Mn–5Ni steel

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Dominating Role of Film‐Like Carbon‐Enriched Austenite for the Simultaneous Improvement of Strength and Toughness in Low‐Carbon Steel

Making low-alloyed steel strong and tough by designing a dual-phase layered structure

Coupled Toughening of a Low Carbon Medium Manganese Heavy Steel Plate Investigated by Electron Back–scattered Diffraction (EBSD)

Ultrahigh Charpy impact toughness (~450J) achieved in high strength ferrite/martensite laminated steels

C-modified stacking-fault networks inducing the excellent strength- plasticity combinations of medium manganese steel by simple two-stage warm rolling without annealing

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

1.0 GPa Low Carbon Medium Mn Heavy Steel Plate with Excellent Ductility

Superior fracture toughness in a high-strength austenitic steel with heterogeneous lamellar microstructure

Design of a high strength, high ductility 12 wt% Mn medium manganese steel with hierarchical deformation behaviour

Achieving High Plasticity and High Toughness of Low-Carbon Low-Alloy Steel through Intercritical Heat Treatment

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Making ultrastrong steel tough by grain-boundary delamination

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Research and development of a new hot rolled laminated structure

Strong and ductile medium manganese steel processed by low-temperature partitioning

Enhancing strength and cryogenic toughness of high manganese TWIP steel plate by double strengthened structure design

A cryogenic ultra-strong and ductile steel induced by stable nanoscale dual-phase structure