Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Mitigating Surface Deficiencies of Perovskite Single Crystals Enables Efficient Solar Cells with Enhanced Moisture and Reverse‐Bias Stability

Improved Crystallinity and Self-Healing Effects in Perovskite Solar Cells Via Functional Incorporation of Polyvinylpyrrolidone

Molecularly Tailored Surface Defect Modifier for Efficient and Stable Perovskite Solar Cells

Moisture-preventing MAPbI3 Solar Cells with High Photovoltaic Performance Via Multiple Ligand Engineering

Multi-Point Collaborative Passivation of Surface Defects for Efficient and Stable Perovskite Solar Cells

Perovskite Surface Passivation Using Thiophene-Based Small Molecules for Efficient and Stable Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Reducing surficial and interfacial defects by thiocyanate ionic liquid additive and ammonium formate passivator for efficient and stable perovskite solar cells

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Efficient and stable planar MAPbI3 perovskite solar cells based on a small molecule passivator

Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells

Incorporation of Small Molecules with Polar Functional Group to Elevate Crystallinity and Suppress Nonradiative Recombination in Perovskite Solar Cells

Defect passivation in perovskite films by p-methoxy phenylacetonitrile for improved device efficiency and stability

Deciphering the Morphology Change and Performance Enhancement for Perovskite Solar Cells Induced by Surface Modification

Interfacial defect passivation by multiple-effect molecule for efficient and stable perovskite solar cells

Bimolecular Crystallization Modulation Boosts the Efficiency and Stability of Methylammonium‐Free Tin–Lead Perovskite and All‐Perovskite Tandem Solar Cells

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Multiple bonding effects of 1-methanesulfonyl-piperazine on the two-step processed perovskite towards efficient and stable solar cells

Surface Modification of PEDOT:PSS for Enhanced Performance of Inverted Perovskite Solar Cells

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells