Abstract:Operational amplifiers with different number of amplifying stages realized on complementarybipolar transistors and input field-effect transistors, with control p-n junction are considered.For the elements of the master slice array MH2XA031 the original electrical schematics of threeamplifier variants (OAmp11.3, OAmp12, OAmp14) containing the same static mode bias blockand output stage are given. The OApm11.3 circuit contains an input differential stage in the formof a " folded" cascode on p-JFETs and an intermediate amplifier stage on bipolar transistors. Theoperational amplifier OAmp12 includes an input dual source-repeater on p-JFETs and an " folded"cascode on complementary bipolar transistors. The OAmp14 circuit is realized on the basis ofdual source repeaters on p-JFETs and a high-precision voltage-to-current converter on complementarybipolar transistors in the intermediate stages. The presented electrical circuits are characterizedby low zero offset voltage, relatively high voltage gain and can be used for application in special and dual-purpose equipment. When designing the Op-Amp circuits on the master slice arrayMH2XA031 the search for a compromise combination of input current, noise level and voltage gainwas carried out, and special attention was paid to the choice of the operating mode of the inputJFETs. Single amplifier stage circuits, which typically provide lower noise, simple frequency correction,and larger bandwidth, were investigated. For an adequate comparison of the developed amplifiersthe modeling of their static and dynamic parameters at the same operating mode of identicalcircuit elements has been performed, which allowed to formulate recommendations on circuit synthesisof operational amplifiers depending on the required combination of parameters. When optimizingthe operating mode of the transistors of the " folded" cascode with input JFETs, the recommendationsconsisting in the necessity to increase the steepness of the input JFET transistors and the voltagedrop across the emitter resistors of the reference current sources were used.

Development of a Small Signal Amplifier with Modeling of BJT-JFET Unit in Sziklai Pair Topology

Small-Signal Amplifiers with BJT, FET and MOSFET in Triple Darlington Topology

Behavioral Modeling for Operational Amplifier in Sigma-Delta Modulators with Verilog-A.

A novel accurate dB-linear control circuit topology for variable gain amplifiers in BiCMOS technology

Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 Μm SiGe BiCMOS

Substrate Integrated Waveguide Based Class‐f Power Amplifier

Design of BJT-JFET Operational Amplifiers on the Master Slice Array

Multiphysics Numerical Method for Modeling Josephson Traveling-Wave Parametric Amplifiers

COMPARATIVE ANALYSIS OF TWO- AND SINGLE-STAGE BJT-JFET OPERATIONAL AMPLIFIERS

Modeling and Harmonic Balance Analysis of Parametric Amplifiers for Qubit Read-out

Importing Experimental Results via S2D Model in ADS Tool for Power Amplifier Design

Development of a RF large signal MOSFET model, based on an equivalent circuit, and comparison with the BSIM3v3 compact model

Simulation of a flux-pumped Josephson parametric amplifier with a detailed SQUID model using the harmonic balance method

Multiparallel Differential JFET Low-Noise Amplifier Circuit Based on Discrete Current Source

Design of a Low-Power High-Gain Bio-Medical Operational Amplifier in 65nm Technology using gm/ID Methodology

Implementation of Electromagnetic Theory: Improved Analysis and Design for Class F Power Amplifier

Modeling and Harmonic Balance Analysis of Superconducting Parametric Amplifiers for Qubit Readout: A Tutorial

Simulation of ﬂux-pumped Josephson parametric ampliﬁer with a detailed SQUID model using harmonic balance method

Fabrication and Characterization of Ultra-Low Noise Narrow and Wide Band Josephson Parametric Amplifiers

A Novel Active Inductor Based Low Noise Amplifier for Analog Front End of Bio-medical Applications

Reconfigurable Low-Power CMOS Amplifier Stages for Broadband Impedance Spectroscopy