Abstract:Schematic of sequential melting and sintering process on morphology development of UHMWPE/LDPE blends. Blending ultra‐high molecular weight polyethylene (UHMWPE) with a low molecular weight polyolefin is a well‐established technique to improve its processability. The binary blends of UHMWPE and low‐density polyethylene (LDPE) were prepared with varying LDPE content (10%, 20%, 30%, 40%, and 50% by wt.) leading to the formation of a single polymer composite system (SPCS) as melting and sintering followed preferential stages during mixing. Interestingly, the sequence of either "melting followed by sintering" or "simultaneous sintering and melting" depends on the LDPE content in the blend, resulting in unique blend morphology. Separate melting peaks for the blend's constituents were observed in thermal characterization, showing the blend's immiscibility, while intermediate peaks showed moderate miscibility in the melt state. Due to the high entanglement density, UHMWPE retained a solid‐like structure and showed an intense viscous nature even above the melting point in rheological characterization. Typically, the UHMWPE samples are fabricated by boundary fusion between particles called sintering. At LDPE content higher than 30 wt.%, the sea island structure was visible in morphological analysis, and the preexisting cavities reduced the tensile modulus by 54% in the blend, along with decreased elongation at failure (250%–100%). Similarly, the flexural modulus was reduced by 34.7% in the blends, along with the decreased flexural strength. Interestingly, the decrease in performance properties occurred in two steps over the range of LDPE content. Thus, it was clear that 30 wt.% of LDPE in the UHMWPE/LDPE blend represented the critical concentration for controlling melting and sintering sequence to develop specified morphology and performance properties. These blends have the potential for biomedical application as well as for the development of foam products, which is the further scope of the present study.

Properties of blends of ultra-high molecular weight polypropylene with various low molecular weight polypropylenes

Polypropylene biocomposites reinforced with bamboo particles and ultrafine bamboo-char: The effect of blending ratio

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Dynamic rheological behavior, crystallization and friction performance of ultrahigh molecular weight polyethylene/polypropylene blends by multi-step melt processing strategy

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

PROGRESS IN ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE/POLYPYLENE BLENDS

Influence of sequential melting and sintering process on morphology development and performance properties of ultra‐high molecular weight polyethylene/low‐density polyethylene blends

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights

Morphology and Mechanical Properties of Blends of Thermoplastic Polyurethane and Polyolefins

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Rheological and optical characterization of Polyvinylpyrrolidone (PVP) - Polyethylene glycol (PEG) polymer blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

Rheological Properties and Morphological Evolutions of Polypropylene/Ethylene-Butene Copolymer Blends

Tribological Property and Tensile Properties of MPU/UHMWPE Blends

Effect of Polymer Blends on the Properties of Foamed Wood-Polymer Composites

Polypropylene Blends with Durable Hydrophobicity and Enhanced Mechanical Properties Based on POSS and Alkane Modified Polypentafluorophenyl Methacrylate