Abstract:Heterogeneous 3D integration is being hailed as the driver for new technologies due to its stacked device architecture. This increases functionality as the number and length of interconnecting wires decreases, in turn decreasing power consumption. In these advanced packaging technologies, the metal redistribution layers (RDLs) and the insulating polymer surrounding them are crucial components on which stringent reliability requirements are placed. The metal RDL’s are necessary to reroute signals from device level to packaging level. The polymer insulator, used as an alternative to traditional dielectric materials, must (i) be photosensitive to be compatible with lithography processing steps, (ii) possess high mechanical strength, (iii) exhibit good electrical performance, (iv) have a high thermal stability and glass transition temperature, and crucially (v) it must not be hygroscopic. Low or no moisture uptake of the polymer is essential as any moisture can cause mechanical and electrical reliability issues. Absorbed moisture can cause oxidation of Cu lines leading to the well-known problem of Cu diffusion resulting in voids, contact issues, delamination, electromigration and higher leakage currents. Area selective deposition (ASD) could greatly benefit these RDL’s by preferentially depositing an oxygen barrier to stop the oxidation of the Cu lines. The proprietary polymer used in this work is part of the WPR series by JSR Corporation and is a thermosetting phenol-based polymer which displays a high mechanical stability as it contains rubber nanoparticles, 70 nm in diameter. These are added to the polymer to increase the toughness and to prevent cracks and fractures forming and propagating through the film. However, achieving ASD with this polymer is difficult as the polymer is designed to have good adhesion properties so it will easily adhere to the Cu in the metal lines, and there are two materials of interest to passivate, the polymer itself and the rubber nanoparticles. In this work the surface is passivated by utilizing a polymerizing octafluorocyclobutane (C 4 F 8 ) plasma which creates a Teflon-like film on the surface. The surface morphology and hydrophobicity are investigated to assess the best plasma exposure time, which was found to be 30 s. Surface chemistry from XPS analysis reveals surface modification through the deposition of fluorine rich groups from the 30 s C 4 F 8 plasma exposure, Figure 1(a). Water contact angle measurements reveal an initial hydrophobic surface (~94°) but this hydrophobicity decreases over the course of several seconds. Following the 30 s C 4 F 8 plasma exposure, the hydrophobicity increases significantly to above 110° and remains stable as shown in Figure 1(b). Surface morphology studies carried out by AFM demonstrates no increase in surface roughness following plasma exposure, Figure 1(c) and (d). ALD tests show the process to be selective to the tetrachloride family of ALD precursors. No selectivity was observed with tetrakis (dimethylamino) or isopropoxide based precursors. This process has the capability to block approximately 2 nm of TiO 2 and HfO 2 from these tetrachloride precursors. Studies of the same process on Cu substrates show that the metal surface is only temporarily modified, and ALD growth can still take place. Reliability stress and corrosion tests were performed to assess if the selectively deposited barriers could prevent Cu oxidation. Figure 1(a) C 1s XPS spectra showing difference before and after plasma treatment, (b) WCA value increases following plasma treatment, and AFM images in (c) and (d) show no change in the surface following plasma exposure. Figure 1

Atomic layer deposition on polymer based flexible packaging materials: Growth characteristics and diffusion barrier properties

Atomic Layer Deposition and Its Applications in Optical Thin Films

Improved Properties of Glass Vials for Primary Packaging with Atomic Layer Deposition

Surface Passivation of Polymer Based Redistribution Layers for Area Selective Deposition of an Oxygen Barrier

Nucleation and growth of gas barrier aluminium oxide on surfaces of poly(ethylene terephthalate) and polypropylene: effects of the polymer surface properties

Growth of ultrathin Al2O3 films on Polydopamine-modified polyethylene terephthalate by atomic layer deposition

Development of high barrier films on flexible polymer substrates

High gas barrier coating using non-toxic nanosheet dispersions for flexible food packaging film

Stretch‐tolerant PECVD gas barrier coatings for sustainable flexible packaging

Few-cycle Atomic Layer Deposition to Nanoengineer Polybenzimidazole for H2/CO2 Separation

Flexible Ultrathin Chip-Film Patch for Electronic Component Integration and Encapsulation using Atomic Layer-Deposited Al2O3-TiO2 Nanolaminates

Selective atomic layer deposition on flexible polymeric substrates employing a polyimide adhesive as a physical mask

Nucleation and Growth Study of Al2O3 Film Fabricated Through Atomic Layer Deposition on Pet Substrate

Plasma Activation and Plasma-assisted ALD Surface Modification of Polymers for Improved Bonding and Adhesive Strength

Rational design of vapor‐deposited self‐crosslinking polymer for transparent flexible oxygen barrier coatings

Multilayer coatings for flexible high-barrier materials

Hybrid organic-inorganic coating with enhanced oxygen- and UV-barrier performance: Polyelectrolyte complex based on sodium alginate, poly (vinyl alcohol), and reconstructed layered double hydroxide

Atomic layer deposition as pore diameter adjustment tool for nanoporous aluminum oxide injection molding masks

Transparent Barrier Coatings Update: Flexible Substrates

High-performance water vapor barriers via amorphous alumina-polycrystalline zinc oxide hybrids with a self-wrinkling morphology

Promising strategies and new opportunities for high barrier polymer packaging films