Abstract:Abstract As the supercritical CO2 power cycle develops and the component technologies mature, there is still a need to reduce the associated capital and operating costs to maintain a competitive levelized cost of electricity (LCOE) in order to enter the market. When considering concentrating solar power (CSP) coupled with an sCO2 power block and sensible thermal storage, the technology presents a clean source for utility-scale power generation to support baseload or peak-load electrical demand. However, the LCOE of the technology is still considered higher than the competing technologies and should be reduced to better compete in the market; 2030 targets for dispatchable solar plants are 5¢/kWh for baseload CSP and 10¢/kWh for peaker plants, as set by the United States Department of Energy. In response to this need, this study is targeting improvements in the power cycle precooler to reduce power block contribution to LCOE. This study considers a dry cooler, as CSP plants are sensitive to water consumption because many installations are slated for remote or arid locations where solar irradiance is very high, but water is scarce. Furthermore, the power block footprint for an sCO2 system is quite compact, especially as compared to a steam cycle. Therefore, there is interest in installing a more compact dry cooler that is proportional to the reduced footprint sCO2 power block, while conventional dry coolers are an order of magnitude larger. The competing goals of size, performance, and cost were considered in this study to develop a compact dry cooler that can easily be packaged with the power block, significantly reducing the installation and transport cost compared to the current state of the art, while maintaining or improving upon the heat transfer performance and impact on plant LCOE. This paper details the high-level findings of a large dry cooler sensitivity study for design point selection, design of the compact dry cooler, expected year-round performance for the dry cooler and the power cycle, and the predicted LCOE for a 30-year plant life. It was found that an aluminum heat exchanger core can be suitably designed to meet the pressure and temperature requirements for a precooler in an sCO2 recompression Brayton cycle. The dry cooler assembly was found to have improved heat transfer performance, allowing for increased cycle efficiencies and a reduced plant LCOE. When coupled with a centrifugal blower and compact transition duct, the dry cooler assembly was able to reduce the installation footprint by over 50%.

Investigation of Thermal and Hydraulic Regime of CDCP for Higher Throughput in SAIL Plant

Optimization of convection cooling by pressed brick structure and coke conversion rate in coke dry quenching furnace

Characterization of coke plant effluent by lysimeter test to evaluate safe disposal to land

CFD-DEM Study on the Synergistic Effect of Coke Consumption and Particle Dynamics in the Blast Furnace Raceway

Computational Study of Heat Exchange and Thermal Oxidative Coking of Supercritical-Pressure Kerosene with Compressed Air in Counterflows

Low CRI, High CSR Coke Trials

Design of a Compact Dry Cooler With an Aluminum Heat Exchanger Core for a Supercritical CO2 Power Cycle Is Evaluated for a Concentrating Solar Power Application

Effect of Coarser Fraction on Coke Strength After Reaction (CSR) of Coke Plant Blend at Tata Steel

Experimental Investigation of Flow Coking and Coke Deposition of Supercritical Hydrocarbon Fuels in Porous Media

Performance assessment and system optimization on supercritical CO 2 double-path recompression coal-fired combined heat and power plants with MEA-based post-combustion CO 2 capture

Resistance characteristics and particle movement behavior of a petroleum coke particle packed bed in a vertical shaft calciner under different burden distribution methods

Optimization of specific energy consumption in the high concentration slurry disposal pipelines for coal ash in thermal power plants

Heat transfer characteristics of petroleum coke particle packed bed: An experimental and CFD simulation study

The comprehensive solution to decrease cooling wall temperatures of sCO2 boiler for coal fired power plant

Heat transfer coefficient evaluated for a designed jacketed vessel for parameter optimization in coal water slurry preparation using dual impellers

Investigation of Supercritical Power Plant Boiler Combustion Process Optimization through CFD and Genetic Algorithm Methods

Experimental and Numerical Investigation of Effect of Inclination on sCO 2 Heat Transfer in a Circular Pipe

Modeling, thermodynamic and techno-economic analysis of coke production process with waste heat recovery

Optimal design and thermodynamic evaluation of supercritical CO 2 oxy-coal circulating fluidized bed power generation systems

Understanding cohesive zone behaviour of blast furnace based on computed tomography flow modelling in a fused bed of ferrous and coke particles

Insights into the gas-solid hydrodynamics and thermochemical characteristics in a pilot-scale chemical looping combustion unit using MP-PIC